Tag Archives: Resetting

Reset driving time indicator Skoda Citigo

Reset driving time indicator Skoda Citigo. From year: 2011, 2012, 2013.
Reset-service-Skoda-Citigo
1. The rocker switch A and the button B are located on the windscreen wiper lever.
2. Select memory.
3. Depress button B.
4. Selecting functions.
5. Briefly push the rocker switch A down or up, this opens the individual functions of the multifunction display one after the other.
6. Resetting, select the driving time indicator.
7. Push the button B for a few seconds.
8. The following readouts of the selected memory will be set to 0 by button B.

Reset oil service light Jaguar XJ

Reset oil service light Jaguar XJ. How to reset maintenance light, reset service light indicator. Can be made manually by use button on car dash board.

How do you reset oil service light Jaguar XJ whit diesel engine. From year: 2008.

  1. Press and hold reset button then turn ignition on.
  2. Release reset.
  3. Press and hold trip button.
  4. When holding trip button, press and hold reset button.
  5. Continue to hold both buttons for 10 seconds ( Message centre should display message like RESETTING SERVICE followed by SERVICE RESET ).

Numbers 1 to 4 need to be done within 3 seconds otherwise it will time out.

Oil service light reset indicator Volvo 850-70

Reset service interval display, insp and oil service for Volvo 850-70, that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Volvo 850-70, oil reset instructions:

RESETTING 5000 MILE SERVICE LAMP ON 1994 + 1995 850

NOTE: This function is for the service reminder lamp, be sure you have performed the proper service such as changing the oil before resetting. If the check engine lamp is illuminated when the car is running, you’ll need to have the car looked at by the Volvo dealer for proper diagnosis.

1. Turn on the ignition to the KPII position so the warning lamps on the dash are illuminated. Do not start the car.

2. Open the bonnet of the car and locate Diagnostic test port (A) behind the driver side headlamp.

3. Remove the cover and pull the jumper wire out of the holder in the cover.

4. Insert the jumper into terminal #7, then press button 4 times, wait approximately 5 seconds and the red lamp should glow continuously. You are now in the data reset mode.

5. Press the button 1 time and wait approximately 5 seconds for the lamp to glow again then press the button 5 times. After about 5 seconds the lamp will illuminate again, press the button 1 time and you will see the lamp flash repeatedly for a couple of seconds indicating that the service lamp has been properly reset.

6. If a mistake is made, simply switch the ignition off and back on to reset and start over.

1996 Model (Some of them)
On these models the diagnostic socket is in front of the gear stick. Switch the ignition on. As you look at the speedometer on the dash, beneath it opposite the trip reset button is a rubber plug. Remove the plug and with a thin pointer such as a ball point pen, depress the pin. This will reset the service light.

1999 Model Service Lamp Reset Procedure

1. Press and hold trip odometer reset button

2. Turn ignition key to run position KPII (not the start position)

3. Wait 30 seconds or until service light begins blinking

4. Release Trip Odometer button

5. Turn ignition to off position

Oil light reset Jeep Renegade Concept

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.

Reset the service oil light on Jaguar S-type

How do you reset maintenance light, reset service light indicator Jaguar S-type. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Jaguar S-type, oil reset instructions:

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.