Tag Archives: service light

Reset oil service light indicator Fiat Ducato 3

How do you reset maintenance light, reset service light indicator Fiat Ducato 3. For reset maintenance light and that can be made manually by use button on car dash board. From year : 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset warning service light on a Fiat Ducato III.

Scheduled servicing ( service ) Fiat Ducato third generation.

Through this function it is possible to display information connected to proper vehicle servicing.

Proceed as follows:

  • Briefly press button MODE: service in km or mi, according to previous setting, will be displayed see paragraph “Units”.
  • Briefly press button MODE to go back to the menu screen or press the button for long to go back to the standard screen.

The “Service schedule” plans different service intervals according to engine models; service interval is displayed automatically, with the ignition key at MAR, starting from 2,000 km (or 1,240 mi) from this deadline and it is shown again every 200 km (or 124 mi). Oil change warning messages are displayed in the same way. Use buttons ▲ and ▼ to display alternately service schedule info and engine oil change info. Below 200 km servicing indications are displayed more frequently. Service indications will be displayed in km or mi according to previous unit setting. When a programmed maintenance interval (coupon) is near to come, turning the ignition key to MAR, the display will show the message “ Service ” followed by the number of km/mi to go before vehicle servicing. Contact a Fiat Dealership to carry out any service operation provided by the “Service schedule” and to reset the display.

Reset oil service light Toyota Tacoma second generation

Reset oil service light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset maint reqd service light Toyota Tacoma 2 generation.

Reset-oil-service-light-Toyota-Tacoma-second-generation.

Engine Oil Replacement Reminder Light (for vehicles sold in U.S.A.).

This light acts as a reminder to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500 miles) after the engine oil replacement, this light illuminates for about 3 seconds and then flashes for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the distance driven exceeds 8000 km (5000 miles), the light will come on after the ignition key is turned to “ON” position. The light will remain on thereafter.

If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. If the light comes on, replace it as soon as possible. The system must be reset after the engine oil replacement. Reset the system by the following procedure:

  1. Turn the ignition key to the “OFF” position with the odometer reading shown. For details, see “Odometer and two trip meters” in this category.
  2. Turn the ignition key to the “ON” position while holding down the trip meter reset knob. See below picture.
  3. How-to-reset-maint-reqd-service-light-Toyota-Tacoma-2-generation.
  4. Hold down the knob for at least 5 seconds. The odometer indicates “000000” and the light goes off.

If the system fails to reset, the light will continue flashing.

All information how can you reset oil service light is taken from Toyota Tacoma second generation owners manual.

 

That it is the full procedure how to reset oil service light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset brake system service light Toyota Tacoma second generation

Reset brake system service light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset brake system service light Toyota Tacoma 2 generation.

This light comes on in the following cases when the ignition key is in the “ON” position.

When the parking brake is applied.

This light comes on for a few seconds when the ignition key is turned to the “ON” position even after the parking brake is released.

When the brake fluid level is low.

It is dangerous to continue driving normally when the brake fluid level is low.

When the hydraulic brake booster fails (with the vehicle stability control system).

If the hydraulic booster causes a problem resulting in poor braking performance, the warning light comes on and buzzer sounds continuously.

Have your vehicle checked at your Toyota dealer in the following case:

  • The light does not come on even if the parking brake is applied when the ignition key is in the “ON” position.
  • The light does not come on even if the ignition key is turned on with the parking brake released.

A warning light turning on briefly during operation does not indicate a problem.

Without the vehicle stability control system.

If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.
  • The brake system warning light re mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

With the vehicle stability control system.

If any of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running.
  • The warning buzzer comes on together with the warning light. In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.
  • The brake system warning light remains on together with the “ABS” warning light.
  • In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

With the vehicle stability control system.

Any of the following conditions may occur, but do not indicate the malfunction:

  • The light may stay on for about 60 seconds after the ignition key is turned to the “ON” position. It is normal if it turns off after a while.
  •  Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the light turns off and the buzzer stops sounding after a few seconds.
  •  You may hear a small sound in the engine compartment after the engine is started or the brake pedal is depressed repeatedly. This is a pump pulsating sound of the brake system, and it is not a malfunction.

All information how can you reset brake system service light is taken from Toyota Tacoma second generation owners manual.

That it is the full procedure how to reset brake system service light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset the oil service light indicator for Volkswagen Tiguan

How do you reset service light indicator Volkswagen Tiguan year 2010, 2011, 2012, 2013

1. Turn the ignition to run (one position before starting engine).
2. Press and HOLD the trip-odometer button “0.0”.
3. Turn your key to run (one position before starting engine).
4. Release the trip-odometer button.
5. Push and release the Clock Minute Set Button “min”.
or
2. Use the rocker switch on the windshield wiper lever to select “Settings” and confirm with button underneath windshield wiper lever then follow steps 4-5.
or
3. Use the buttons on the right hand side of the multi function steering wheel
4. Select the “Settings” menu followed by the “Service” submenu. Select “Reset” and confirm.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
*vehicles equipped with a navigation system can also access the reset menu from the SETTINGS button.

Oil reset service light indicator Dacia Logan MCV DCI.

How do you reset maintenance light, reset service light indicator Dacia Logan MCV DCI. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Dacia Logan MCV DCI, oil reset instructions:

Dacia-Logan-MCV-1.5-dCi

How reset oil light service Dacia Logan MCV DCI

1. Switch ignition ON.
2. Press and hold the throttle pedal
3. Press the brake pedal 3 times

Perform all operations in less than 10 seconds

Oil change warning light should turn off.