Reset service light indicator Seat Arosa. From year: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004.
How to reset service light indicator Seat Arosa.
1. With the ignition switched off.
2. Push and hold the tripmeter reset button situated below the speedometer.
3. Turn the ignition on and hold the tripmeter reset button for atleast 8 sconds.
4. On board will appear “- – – -” done the service light has been reset.
5. It may not works on the first try, you must retry the procedure.
Reset service light indicator Seat Inca. From year: 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003.
How to reset service light indicator Seat Inca.
1. Turn on the ignition, do not start the engine.
2. Push and holf the left hand button on the clocks.
3. With the button still pressed turn the ignition to off.
5. Release the button and you should be able to toggle between the oil, insp1 and insp2 warning light.
6. Choose the warning light that you want to reset.
7. On the right hand side of the clocks there are 2 buttons.
8. Push the bottom button with a biro and hold it until the warning light is reset.
Hot to reset service light on a Seat Inca
Try this.
Switch on the ignition.
Press the left hand button on the clocks and hold it in while switching off the ignition.
Release the button and you should be able to toggle between the oil, insp1 and insp2 indicators.
Choose the one you want to reset.
On the right hand side of the clocks there is two buttons.
Press and hold the bottom button with a biro and hold it until the display is reset.
Hot to reset service light on a Seat Arosa
The SEAT owners manual for the Arosa states.
With the ignition switched off, press and hold the trip meter reset button below the speedometer.
Then, switch the ignition on and hold the reset button for atleast 10 sconds.
Dashes will then appear in the display.
The service has been reset.
Service indicator system Seat Cordoba, 1993, 1994, 1995, 1996, 1997, 1998, 1999
IN00, No service is required, standard display.
OEL, When 7500 miles has been reached before the yearly service is required.
IN01, Indicates time for the yearly service inc oil change.
IN02, Indicates it is time for the Major service. T
O RESET THE INDIVIDUAL COUNTERS.
1) turn on ignition (do not start).
2) Press the trip reset button button on the speedo (the trip value will not reset to zero but will reappear when the procedure is finished).
3) Turn off the ignition and thne release the trip reset button. In the LCD display you will see the word OEL. Using the minute set button for the clock (lower one) you will reset the OEL interval counter. Press it, hold, release, 5 horizontal lines will appear in the display.
4) press and release the trip reset button. In the LCD display you will see IN01 repeat step 3 to reset the inspection counter when required.
5) Again press the trip reset and rest the IN02 counter if necessary. If doing an oil change only reset the OEL counter. If doing an inspection service reset both the OEL and IN01 counters. If doing a full service reset all 3, OEL, IN01 and ,IN02.
6) Turn on ignition (do not start the car).
7) After the appearance of the IN00 display turn off the ignition.
8) You are done the trip counter should read as it did before you started.
PROGRAMMING THE INTERVALS TO REQUIREMENTS
With todays higher spec oils and/or peoples need and desire to service more regular there is a way to alter the counters to your prefered settings (within reason).
1) Turn on ignition (dont start the car).
2) press the trip reset button also press the Minute set button on the clock (lower one).
3) The LCD display OEL 1,S where the S indicates SET.
4) Using the trip reset button you can call up the following counter data in sequence.
OEL 1,S Distance counter for oil change (7500 standard).
OEL 2,S Time counter for oil change (12 months).
IN 01,S Time counter for yearly service interval (12 months).
IN 02,S Distance counter for full service (15000 miles).
5) Using the minute SET button on the clock (lower one) you can display the current value repeated pressing of the button will select a subsequent lower value and at the lowest level will reset to the highest and start to decrease again (so dont panic). the steps work in miles (500 at a time) and time steps in bi-monthly (1, 2months) i.e.1,2,3,4,5,6.
6) Once you have set the counter to the value you require turn off the ignition.
7) Job done