Category Archives: Uncategorized

Reset service light oil life indicator dashboard Chrysler Town & Country

Leave a reply

How do you reset maintenance light, reset service light indicator Chrysler Town & Country, year 2014, 2015. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Chrysler Town & Country, year 2014, 2015 oil reset instructions:

  1. Turn the ignition to run.
    *one position before starting engine
  2. Fully depress the accelerator pedal slowly three times within 10 seconds.
  3. Turn the ignition off and then start the engine to verify the indicator has been reset.

MAINT REQ’D Reset & Service Specifications Toyota Camry 2013

Leave a reply

MAINT REQD light can be reset by doing the following:

1. Press the “”ENGINE START STOP”” switch once (do not start the engine) or turn ignition key to run (one position before starting the engine).
2. Ensure Trip Metre A reading is shown. Turn the ignition off.
3. Press and hold the display change button and turn the ignition on (do not start the engine).
4. Continue to press and hold the button until the trip meter displays “”000000″”.”
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset service light Toyota Sequoia first generation

Leave a reply

Reset VSC trac warning light Toyota Sequoia first generation. From year: 2005, 2006, 2007.

How to reset VSC trac warning light Toyota Sequoia 1 generation.

This light warns that there is a problem somewhere in the vehicle stability control system and traction control system (two−wheel drive models) or active traction control system (four−wheel drive models). The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

    • All information how can you reset VSC trac warning light is taken from Toyota Sequoia owners manual.

    How reset oil light GMC Sierra

    Leave a reply

    How do you reset maintenance light, reset service light indicator GMC Sierra. For reset maintenance light and that can be made manually by use button on car dash board.

    Reset service light indicator, engine oil life GMC Sierra, oil reset instructions:

    year 2001-2007

    1. Turn the ignition to run (one position before starting engine).
    2. Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
    3. If the Change Oil Soon light flashes the system is resetting.
    4. Turn the ignition off and then start the engine to verify the indicator has been reset.

    year 2008-2013

    1. Turn the ignition to run (one position before starting engine).
    2. *Display the OIL LIFE REMAINING on the DIC (i button). If the vehicle does not have DIC buttons, the vehicle must be in P (Park) to access this display by pressing the trip odometer reset stem.
    3. Press and hold the SET/RESET (arrow) button on the DIC, or the trip odometer reset stem if the vehicle does not have DIC buttons for more than 5 seconds. The oil life will change to 100%.
    4. Turn the ignition off and then start the engine to verify the indicator has been reset.
    *Remaining oil life can also be reset by depressing the gas pedal 3 times within 5 seconds instead of using the DIC.

    Reset the '07 Porche 911 Carrera Oil Change

    Leave a reply

    Instructions

    1. Push inward on the trip odometer reset button and turn the key to the auxiliary position (forward one click from the off position) until “Oil Service Re” or “Oil Service Reset” appears on the odometer screen.

    2. Press the odometer reset button a second time until the work “Reset” or “Re” appears on the screen. The word will continuously flash.

    3. Press the odometer reset button quickly to complete the reset. “End SIA” appears to indicate a successful reset of the system.