Tag Archives: minute

Reset light airbag fault code Range Rover

How to reset airbag fault code Range Rover.

Reset airbag fault code Range Rover. How to reset the Range Rover Airbag Fault Code warning light. Reset AIRBAG FAULT error message on dash board on a Range Rover.

Instructions:

  1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.
  2. Slide the clamp off of the negative battery terminal.
  3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.
  4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.

SERVICE INDICATOR SYSTEM SEAT CORDOBA

Service indicator system Seat Cordoba, 1993, 1994, 1995, 1996, 1997, 1998, 1999

IN00, No service is required, standard display.

OEL, When 7500 miles has been reached before the yearly service is required.

IN01, Indicates time for the yearly service inc oil change.

IN02, Indicates it is time for the Major service. T

O RESET THE INDIVIDUAL COUNTERS.

1) turn on ignition (do not start).

2) Press the trip reset button button on the speedo (the trip value will not reset to zero but will reappear when the procedure is finished).

3) Turn off the ignition and thne release the trip reset button. In the LCD display you will see the word OEL. Using the minute set button for the clock (lower one) you will reset the OEL interval counter. Press it, hold, release, 5 horizontal lines will appear in the display.

4) press and release the trip reset button. In the LCD display you will see IN01 repeat step 3 to reset the inspection counter when required.

5) Again press the trip reset and rest the IN02 counter if necessary. If doing an oil change only reset the OEL counter. If doing an inspection service reset both the OEL and IN01 counters. If doing a full service reset all 3, OEL, IN01 and ,IN02.

6) Turn on ignition (do not start the car).

7) After the appearance of the IN00 display turn off the ignition.

8) You are done the trip counter should read as it did before you started.

PROGRAMMING THE INTERVALS TO REQUIREMENTS

With todays higher spec oils and/or peoples need and desire to service more regular there is a way to alter the counters to your prefered settings (within reason).

1) Turn on ignition (dont start the car).

2) press the trip reset button also press the Minute set button on the clock (lower one).

3) The LCD display OEL 1,S where the S indicates SET.

4) Using the trip reset button you can call up the following counter data in sequence.

OEL 1,S Distance counter for oil change (7500 standard).

OEL 2,S Time counter for oil change (12 months).

IN 01,S Time counter for yearly service interval (12 months).

IN 02,S Distance counter for full service (15000 miles).

5) Using the minute SET button on the clock (lower one) you can display the current value repeated pressing of the button will select a subsequent lower value and at the lowest level will reset to the highest and start to decrease again (so dont panic). the steps work in miles (500 at a time) and time steps in bi-monthly (1, 2months) i.e.1,2,3,4,5,6.

6) Once you have set the counter to the value you require turn off the ignition.

7) Job done

Reset the Range Rover Airbag Fault Code

Instructions

1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.

2. Slide the clamp off of the negative battery terminal.

3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.

4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.

Reset computer after oil change on 2006 bmw 325xi

Turn the car on. Wait about a minute for the computer to get to normal.
press and hold the travel mile reset button. Hold it untill an ! in a triangle appears. then your maintanance info will pop up. select the item to reset. and tap the side button on the wand atached to the stearing wheel. this button is what you use to browse through your computer. press the button once it will say “reset” press and hold it the second time and it will say reset, hold for 5 seconds or so and it will show a check mark next to “reset” confirming it has reset.

Oil service reset Volkswagen Tiguan

Reset service light indicator, engine oil life Volkswagen Tiguan, year 2009-2010 reset instructions:

Manual Reset:
Turn the ignition to run (one position before starting engine).
Press and HOLD the trip-odometer button “0.0”.
Turn your key to run (one position before starting engine).
Release the trip-odometer button.
Push and release the Clock Minute Set Button “min”.
Turn the ignition off and then start the engine to verify the indicator has been reset.