Tag Archives: value

Fiat Ducato 3 reset trip computer

Leave a reply

How to reset trip computer on a Fiat Ducato III.

Reset trip computer Fiat Ducato 3. From year : 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

The “trip computer” displays information (with ignition key at MAR), relating to the operating status of the vehicle. This function comprises two separate and independent trips: “Trip A” and “Trip B” concerning the “complete mission” of the vehicle (journey).

Both functions are resettable, reset – start of new mission.

“Trip A” shall be used to display the figures relating to:

External temperature.
Range.
Trip distance.
Average consumption.
Instant consumption.
Average speed.
Travel time (driving time).
“Trip B”, available on multifunction display only, shall be used to display the figures relating to:

Trip distance B.
Average consumption B.
Average speed B.
Travel time B (driving time).
“Trip B” function can be excluded (see paragraph “Trip B On/Off”). “Range” and “Instant consumption” cannot be reset.

Values displayed Fiat Ducato 3 third generation.

External temperature.

It indicates the external temperature of the driver compartment.

Range.

This value shows the distance in km (or mi) that the vehicle can still cover before needing fuel, assuming that driving conditions are kept unvaried. The display will show “—-” in the following cases:

value lower than 50 km (or 30 mi).
vehicle left parked with engine running for long.
Trip distance Fiat Ducato 3. This value shows the distance covered from the start of the new mission.

Average consumption Fiat Ducato 3. This value shows the average consumption from the start of the new mission.

Instant consumption Fiat Ducato 3. This value shows instant fuel consumption (this value is updated second by second). If parking the vehicle with engine on, the display will show “—-”.

Average speed Fiat Ducato III. This value shows the vehicle average speed as a function of the overall time elapsed since the start of the new mission.

Travel time Fiat Ducato III. This value shows the time elapsed since the start of the new mission.

IMPORTANT Lacking information, Trip computer values are displayed with “—-”. When normal operating condition is reset, calculation of different units will restart regularly. Values displayed before the failure will not be reset.

Button TRIP, set on the top of the right steering column stalk, shall be used (with ignition key at MAR) to display and to reset the previously described values to start a new mission:

short push to display the different vaues.
long push to reset and then start a new mission.
New mission Fiat Ducato 3.

Reset can be:

“manual” resetting by the user, by pressing the relevant button;
“automatic” resetting, when the “Trip distance” reaches 3999,9 km or 9999,9 km or when the “Travel time” reaches 99.59 (99 hours and 59 minutes);
after disconnecting/reconnecting the battery.
IMPORTANT The reset operation in the presence of the screens concerning the “Trip A” makes it possible to reset only the information associated with this function.

IMPORTANT The reset operation in the presence of the screens concerning the “Trip B” makes it possible to reset only the information associated with this function.

Start of journey procedure. With ignition key at MAR, press and keep button TRIP pressed for over 2 seconds to reset.

Exit Trip – to quit the Trip function: keep button MODE pressed for over 2 seconds.

Oil reset service light indicator Mercedes Viano 2008

Leave a reply

How do you reset maintenance light, reset service light indicator Mercedes Viano, year 2008, 2009, 2010, 2011, 2012, 2013, 2014. For reset maintenance light and that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Mercedes Viano, oil reset instructions:

  1. Ensure ignition is switched OFF.
  2. Switch ignition ON and briefly press button[A] twice.
  3. Within 10 seconds: Switch ignition OFF.
  4. Press and hold button [A].
  5. Switch ignition ON.
  6. Continue to hold button [A].
  7. The remaining distance will be displayed.
  8. After aproximately 10 seconds a warning sound will be heard and the new remaining distance will appear in the digital display.
  9. Release button [A].

Oil reset service light indicator Mercedes Viano 2008

NOTE: The service interval indicator can be reset to a higher than normal value for use with alternative higher specification engine oils. This can only be carried out using diagnostic equipment.

Timing Belt Warning Indicator Reset Procedure For LandCruiser

Leave a reply

Reset Procedure For Toyota LandCruiser UZJ100, HZJ105 and HDJ100

1. T-BELT MODE DISPLAY
a) With ignition turned ON, using the trip switch (select/reset button) change the display to ODO, and turn the ignition OFF
b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds.
c) Release the trip switch, then press the switch again within 5 seconds.
d) The digital display should change to T-belt mode. The initial display “15” (0,000km) is displayed (ie. 150,000km).

2. REWRITING REPLACEMENT VALUES
While in the T-Belt mode, each press of the trip switch will change the displayed value by 10,000km increments. Once ” 20 ” (200,000km) is reached the display reverts back to ” 1 ” (10,000km) again. Remember, this setting is the number of kilometres to be travelled before the light comes on next, and once reset this counter will start from zero.
I believe the timing belt interval for all the 100 series engine variants is 150,000km, but this should be checked against each different markets servicing recommendation. This being the case, you shouldn’t need to change from the default setting of “15”.
Obviously for the US, the ODO is in miles, and I guess the T-Belt warning would be set in 10,000 mile intervals.

3. T-BELT WARNING RESET COMPLETION
a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch.
b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
NOTE: If the T-Belt mode is completed, even though the belt replacement has not been performed, the T-Belt warning IS reset.
I hope this proves to be of assistance guys, as usual all care no responsibility. ;-)

Reset oil service light Ford Explorer Sport Trac

Leave a reply

Reset oil service light Ford Explorer Sport Trac. From years: 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010.

How do you reset oil service light Ford Explorer Sport Trac. From years:1999, 2000, 2001.

  1. Turn the ignition to run, one position before starting engine.
  2. Press and hold the OIL CHANGE RESET control for 5 seconds. The message centre will count down for 5 seconds and the message centre will display OIL LIFE RESET TO 100%.
  3. Turn the ignition off and then start the engine to verify the indicator has been reset.

 

How to reset oil service light Ford Explorer Sport Trac. From years: 2002, 2003.

  1. Turn the ignition to run , ne position before starting engine.
  2. Press the SETUP control to access the System Check function.
  3. Press and release the RESET control to display OIL LIFE XX% HOLD RESET NEW.
  4. Press and hold the RESET control for 2 seconds to display IF NEW OIL HOLD RESET.
  5. Press and hold the RESET control to display OIL LIFE SET TO 100%. Your oil life is now reset.
  6. Turn the ignition off and then start the engine to verify the indicator has been reset.

 

Full procedure how to reset oil service light Ford Explorer Sport Trac. From years: 2004, 2005.

  1. Turn the ignition to run, one position before starting engine.
  2. Select this function from the SETUP control PRESS RESET AT OIL CHANGE.
  3. Press RESET control to reset oil change.
  4. Turn the ignition off and then start the engine to verify the indicator has been reset.

 

How can you reset oil service light Ford Explorer Sport Trac. From years: 2006, 2007.

To reset the oil monitoring system to 100% after each oil change Ford Explorer Sport Trac. From years: 2006, 2007 [approximately 5,000 miles (8,000 km) or 180 days] perform the following.

  1. Turn the ignition to run, one position before starting engine.
  2. Enter SYSTEM CHECK to display “OIL XXX% OIL LIFE OK”.
  3. Press RESET control to display “HOLD RESET IF NEW OIL”.
  4. Press and hold the RESET control for more than 2 seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed.

Note: To change oil life 100% miles value from 5,000 miles (8,000 km) or 180 days to another value, refer to the Oil Life Start Value selected from the SETUP MENU in this section.

Reset Oil life Start Value Ford Explorer Sport Trac. From years: 2006, 2007.

  1. Select this function from the SETUP control for the current display mode.
  2. Each press of the RESET control reduces the value by 10 percent.

Note: Oil Life Start Value of 100% equals 5,000 miles (8,000 km) or 180 days. For example, setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,828 km) and 120 days.

 

 

How do you reset oil service light Ford Explorer Sport Trac. From years:2008, 2009, 2010.

To reset the oil monitoring system to 100% after each oil change Ford Explorer Sport Trac. From years: 2008, 2009, 2010 [approximately 7,500 miles (12,070 km) or 6 months] perform the following.

  1. Turn the ignition to run, one position before starting engine.
  2. Press RESET control to display “HOLD RESET IF NEW OIL”.
  3. Press and hold the RESET control for more than 2 seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed.
  4. Note: To change oil life 100% miles value from 7,500 miles (12,070 km) or 6 months to another value, proceed to step 5.
  5. Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET control switch to change the Oil Life Start Value. Each release and press will reduce the value by 10 percent.
  6. Note: Oil Life Start Value of 100% equals 7,500 miles (12,070 km) or 6 months. For example, setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,828 km) and 120 days.

OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 0%.

An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule.

ENGINE OIL CHANGE SOON. Displayed when the engine oil life reaches 5% or less of the Oil Life Start Value.

Reset oil service light Ford E 150 Series

Leave a reply

Reset oil service light Ford E 150 Series. From years: 2009, 2010, 2011, 2012.

How to reset oil service light Ford E 150 Series.

Oil Life Reset and Start Value.  An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule.

To reset the oil monitoring system to 100% after each oil change Ford E 150 Series. From years: 2009, 2010, 2011, 2012 (approximately 7,500 miles [12,000 km] or six months) perform the following.

  1. Switch the ignition ON, do not start the engine.
  2. Press and release the SELECT/RESET stem to display “OIL LIFE = XXX% HOLD RESET = NEW”.
  3. Press and hold the SELECT/RESET stem for two seconds and release. Oil life is set to XX% and “OIL LIFE SET TO XXX%” is displayed.
  4. To change oil life 100% miles value from 7,500 miles (12,000 km) or six months to another value, proceed to Step 5.
  5. Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET control switch to change the Oil Life Start Value. Each release and press will reduce the value by 10%.

Note: Oil Life Start Value of 100% equals 7,500 miles (12,000 km) or six months. For example, setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,800 km) and 120 days.

OIL LIFE CHANGE SOON. Displayed when the engine oil life remaining is 5% or less. When oil life left is between 5% and 0%, the ENGINE OIL CHANGE SOON message will be displayed.

OIL CHANGE REQUIRED. Displayed when the oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed. OIL LIFE OK displays after you have changed the oil.