Tag Archives: number

Timing Belt Warning Indicator Reset Procedure For LandCruiser

Reset Procedure For Toyota LandCruiser UZJ100, HZJ105 and HDJ100

1. T-BELT MODE DISPLAY
a) With ignition turned ON, using the trip switch (select/reset button) change the display to ODO, and turn the ignition OFF
b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds.
c) Release the trip switch, then press the switch again within 5 seconds.
d) The digital display should change to T-belt mode. The initial display “15” (0,000km) is displayed (ie. 150,000km).

2. REWRITING REPLACEMENT VALUES
While in the T-Belt mode, each press of the trip switch will change the displayed value by 10,000km increments. Once ” 20 ” (200,000km) is reached the display reverts back to ” 1 ” (10,000km) again. Remember, this setting is the number of kilometres to be travelled before the light comes on next, and once reset this counter will start from zero.
I believe the timing belt interval for all the 100 series engine variants is 150,000km, but this should be checked against each different markets servicing recommendation. This being the case, you shouldn’t need to change from the default setting of “15”.
Obviously for the US, the ODO is in miles, and I guess the T-Belt warning would be set in 10,000 mile intervals.

3. T-BELT WARNING RESET COMPLETION
a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch.
b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
NOTE: If the T-Belt mode is completed, even though the belt replacement has not been performed, the T-Belt warning IS reset.
I hope this proves to be of assistance guys, as usual all care no responsibility. ;-)

Reset Service Indicator of BMW 3 E46 Chassis

Turn key switch ON or when start engine, the instrument panel will display “OIL Service” or“INSPECTION” and left distance for several seconds. If “Service” or“ INSPECTION” are lit all the time and the left distance is next to “0”? it indicates that it needs oil service reset.

Reset by manual :
1. Press RESET button in the left of instrument panel.
2. Turn key ON and to ACC position.
3. Waiting for the instrument displays “OIL Service” or “INSPECTION” is flashed.
4 Release RESET button, then press five seconds, the screen will display RESR or RE is flashed. Release RESET button again and press again till the screen displays “25000km”. Now reset is completed.

When you find there is “-“symbol in front of the left distance number in the screen, and you can’t do reset with the above method, now you can use X-431 to reset oil service.

Reset the service light on a mini cooper 2007

Service Reset:

1)Push-hold Trip Button (TB)
2)Turn key to position 1
3)Continue to hold (TB), the number 15A will show to the teft of the milage
4)Release (TB) for 3 sec and then hold (TB) again
5)In about 5-8 sec RST will show in the left corner
6)Release and then hold again 15000 will show, press and release
7)Car is now reset to the 15,000 service – (has completed 10,000 mile service) and will count down from 15,000.

Oil service reset Silhouette

2000

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the CHANGE OIL SOON indicator flashes 2 times.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2001-2004

Turn the ignition to run (one position before starting engine).
Repeatedly push the TRIP/RESET button until OIL is displayed on the Driver Information Centre.
Push and hold the RESET button for 5 seconds. The number will disappear and be replaced by 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Saturn Relay

2005-2007

Turn the ignition to run (one position before starting engine).
Push the set/reset button until OIL is displayed on the DIC.
Once OIL is displayed, push and hold the set/reset button for 5 seconds. The number will disappear and be replaced by 100 (indicating 100% oil life remaining).
Turn the ignition off and then start the engine to verify the indicator has been reset.