Tag Archives: parking brake

Reset brake system warning light Toyota Land Cruiser 100 series

Leave a reply

How to reset brake system warning light Toyota Land Cruiser 100 series.

Reset brake system warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light comes on in the following cases when the ignition key is in the “ON” position.

When the parking brake is applied.

This light comes on for a few seconds when the ignition key is in the “ON” position even after the parking brake is released.

When the brake fluid level is low.

It is dangerous to continue driving normally when the brake fluid level is low.

When the hydraulic brake booster fails.

If the hydraulic booster causes an problem resulting in poor braking performance, the warning light comes on and buzzer sounds continuously.

Have your vehicle checked at your Toyota dealer in the following cases:

The light does not come on even if the parking brake is applied when the ignition key is in the “ON” position.
The light does not come on even if the ignition key is turned on with the parking brake released.
A warning light turning on briefly during operation does not indicate a problem.

If any of the following conditions occur, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running.
  • The warning buzzer comes on together with the warning light.
  • In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.

The brake system warning light remains on together with the “ABS” warning light.

In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

Any of the following conditions may occur, but do not indicate a malfunction:

The light may stay on for about 60 seconds after the ignition key is turned to “ON” position. It is normal if it goes out after a while.

Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the light goes out and the buzzer stops sounding after a few seconds.

You may hear a small sound in the engine compartment after the engine is started or the brake pedal is depressed repeatedly. This is a pump pulsating sound of the brake system, and it is not a malfunction.

All information how can you reset brake system warning light is taken from Toyota Land Cruiser 100 series owners manual.

How to check service reminder light Toyota Solara 2 generation

Leave a reply

How to check service reminder light Toyota Solara 2 generation. From year: 2004, 2005, 2006, 2007, 2008.

How can you check service reminder light Toyota Solara second generation.

CHECKING SERVICE REMINDER INDICATORS except the low fuel level warning light and low windshield washer fluid level warning ligh).

  1. Apply the parking brake.
  2. Open one of the doors. The open door warning light should come on.
  3. Close the door. The open door warning light should go off.
  4. Turn the ignition key to “ON”, but do not start the engine. All the service reminder indicators except the open door warning light should come on. The “ABS”, “VSC” and low tire pressure warning lights, engine oil replacement reminder light, “TRAC OFF” and slip indicator lights go off after a few seconds. The SRS warning light goes off after about 6 seconds.

If any service reminder indicator or warning buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.

All information how to check service reminder light is taken from Toyota Solara 2 generation owners manual.

That it is the full procedure how to check service reminder light Toyota Solara 2 generation Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

Reset brake system service light Toyota Tacoma second generation

Leave a reply

Reset brake system service light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset brake system service light Toyota Tacoma 2 generation.

This light comes on in the following cases when the ignition key is in the “ON” position.

When the parking brake is applied.

This light comes on for a few seconds when the ignition key is turned to the “ON” position even after the parking brake is released.

When the brake fluid level is low.

It is dangerous to continue driving normally when the brake fluid level is low.

When the hydraulic brake booster fails (with the vehicle stability control system).

If the hydraulic booster causes a problem resulting in poor braking performance, the warning light comes on and buzzer sounds continuously.

Have your vehicle checked at your Toyota dealer in the following case:

  • The light does not come on even if the parking brake is applied when the ignition key is in the “ON” position.
  • The light does not come on even if the ignition key is turned on with the parking brake released.

A warning light turning on briefly during operation does not indicate a problem.

Without the vehicle stability control system.

If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.
  • The brake system warning light re mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

With the vehicle stability control system.

If any of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running.
  • The warning buzzer comes on together with the warning light. In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.
  • The brake system warning light remains on together with the “ABS” warning light.
  • In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

With the vehicle stability control system.

Any of the following conditions may occur, but do not indicate the malfunction:

  • The light may stay on for about 60 seconds after the ignition key is turned to the “ON” position. It is normal if it turns off after a while.
  •  Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the light turns off and the buzzer stops sounding after a few seconds.
  •  You may hear a small sound in the engine compartment after the engine is started or the brake pedal is depressed repeatedly. This is a pump pulsating sound of the brake system, and it is not a malfunction.

All information how can you reset brake system service light is taken from Toyota Tacoma second generation owners manual.

That it is the full procedure how to reset brake system service light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset the oil service light 2011 Ford Fiesta

Leave a reply

To reset the oil service light, use the following procedure:

1. With the ignition in the off position, press the brake and accelerator pedals.
2. For keyed vehicles, turn the key to the accessory position; for pushbutton start vehicles, press the Start/Stop button once quickly. Do not start the engine.
3. Press the accelerator and brake pedals fully for 20 seconds.
4. “Engine Oil Change Due Next Service” and the oil service light will display.
5. Turn the vehicle off. The message and lights will be cleared.

Normal Maintenance

Under what Ford terms “normal” conditions, oil changes will occur at a maximum of every 10,000 miles (16,000 kilometers) or 12 months. Other services to be performed at every oil change include:
• Rotate tires.
• Inspect wheels and related components for noise, wear, looseness or drag.
• Inspect brake pads, shoes, rotors, drums, brake linings, hoses and parking brake.
• Inspect engine cooling system for strength; inspect cooling system hoses.
• Inspect exhaust system and heat shields.
• Inspect half-shaft boots.
• Inspect and lubricate steering linkage, ball joints, suspension, tie-rod ends and U-joints if equipped with grease fittings.
• Inspect cabin air filter (if equipped).

How to Change the Rear Brake Pads on a VW Passat

Leave a reply

Remove the old Brake Pads

1. Park your car on a level surface. If you have a stick shift car make sure the car is in gear. Do not set the parking brake. Place blocks in front of the front tires so the car does not move while you are working on it.

2. Open the hood of your car and locate the master cylinder. If necessary, remove brake fluid until the level in the container is less than half full. A turkey baster is a good tool for this. Put the brake fluid in the plastic container and dispose of it the way you dispose of motor oil.

3. Raise the rear end of your car with your car jack. Remove the rear tire or wheel assembly.

4. Remove the parking brake cable from the back of the caliper. Use the pliers to remove the cable clip (restraining clip).

5. Use the socket wrench to remove the upper mounting bolt from the caliper. If the upper guide pin moves while you do this, use a back-up wrench to hold the upper guide pin.

6. Rotate the caliper downward, pivoting it on the lower caliper bolt. Remove the inner and outer brake pads from the caliper.

Install the new Brake Pads

1. Turn the caliper piston clockwise to retract it into the caliper housing. Insert the new brake pads into the caliper.

2. Swing the caliper upward and into place. Apply a thin coat of thread locking compound to the bolt and use the socket wrench to tighten the bolt to 271 inch lb. (35 Nm).

3. Reattach the parking brake cable to the caliper.

4. Replace the tire wheel assembly. Lower the car to the ground.

5. Pump the brake pedal a few times to seat the brake pads. Do this before trying to move your car.

6. Add fluid to the master cylinder container to replace any you removed before you removed the old brake pads.

7. Season the brake pads by making only gentle stops when you are driving for the first week after you install the new brake pads. Try not to do any hard stopping when you are seasoning the brakes.