Tag Archives: Instructions

Reset the Service B in a Mercedes C230

Leave a reply

Reset service light indicator, engine oil life Service B in a Mercedes C230, oil reset instructions:

When a service is needed based on the car’s mileage or time since the last service, the display screen on a Mercedes C230 will notify you. The display screen is located within the speedometer on the instrument panel. Mercedes mechanics will reset the Service B notification light after the service is performed. If you performed the service, you need to reset the light yourself. Service B includes an oil and filter change, a tire rotation and other maintenance checks.

Instructions

1. Insert the key into the ignition and turn it until the battery comes or the engine turns on.

2. Locate the left and right arrow buttons on the left side of your steering wheel. Press either button until the mileage is displayed on the instrument panel display screen.

3. Press the up or down button until the service symbol appears on the screen.

4. Locate the trip odometer reset button to the left of the instrument panel. Hold the reset button for a few seconds until the screen displays the message, “Do you want to reset the service interval? Confirm with the R-button.” Release the button once the phrase appears.

5. Press the reset button to reset the Service B notification.

Oil light reset Jeep Renegade Concept

Leave a reply

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.

Reset the service oil light on Jaguar S-type

Leave a reply

How do you reset maintenance light, reset service light indicator Jaguar S-type. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Jaguar S-type, oil reset instructions:

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Oil service reset Lincoln LS

Leave a reply

How do you reset maintenance light, reset service light indicator Lincoln LS, year 2000, 2001, 2002, 2003, 2004, 2005, 2006. For reset maintenance light and that can be made manually by use button on car dash board.

Instructions to reset service indicator 2000-2006

  • Turn the ignition to run (one position before starting engine).
  • Press the STATUS control to access the System Check function.
  • Press RESET to reset oil %.
  • Press and hold the RESET control to set to 100%. After a successful reset, the message centre will display OIL LIFE SET TO 100%.
  • Turn the ignition off and then start the engine to verify the indicator has been reset.

How to Reset the Service Light on a Jeep

Leave a reply

Instructions

Things You’ll Need
Wrench
Ignition key
OBDl or ll scanner

1. Disconnect your battery cables from the battery posts with a 6-pt. closed wrench in the size appropriate for the battery bolts. Remove the negative (black) cable first. Leave the battery disconnected for several minutes, according to Allpar.com. Reconnect, this time starting with the positive cable, and crank the engine. The code should be gone.

2. Crank the Jeep. Drive it forward, then backwards, and shut off. Repeat this procedure three times. The codes should clear on the fourth crank.

3. Use a OBDl or OBDll scan tool. Plug the tool into your Jeep’s ALDL (Assembly Line Diagnostic Link), a small, rectangular electrical port usually located under the dash. Turn the key to the “on” position. Scan the computer for codes and select the option to clear the codes.

4. Wait for the code to clear itself automatically. Once the component is fixed, the check engine light disappears after several successful ignitions. The code is then stored for a while. If the engine continues to start and run without a re-occurrence of the original problem, the code is wiped out.