Tag Archives: Instructions

Oil reset service light indicator Opel Corsa D

Leave a reply

Instructions how reset service light indicator Opel Corsa D. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.

There are two ways to reset service light Opel Corsa d.

1. How to reset service light indicator Opel Corsa D.

  1. Get into the car and shut all doors.
  2. Wait for the milage (km) and displays to go off .
  3. Press and hold the brake pedal.
  4. Press and hold the trip reset button at the same time with the brake.
  5. Turn on the ignition to the point where all the lights come on, do not start the engine.
  6. The mileage (km) will come up on the dash and then InSP with four dashes “—-” will appear, do not release the trip button and brake pedal.
  7. Continue to hold the trip button and brake pedal for about 15 seconds.
  8. At this point it should flash up insp and then the reset mileage 15,000-30,000.
  9. Now you can release the trip button and brake pedal, the indicator is reset.

2. How do you reset service light indicator Opel Corsa D.

  1. Ignition OFF.
  2. Press and hold reset trip odometer button.
  3. Turn the ignition on, one position before starting engine.
  4. The letters InSP and symbol “- – – – ” will appear in the display.
  5. Kepp the trip odometer button for about 15 seconds.
  6. At this point it should flash up insp and then the reset mileage 15,000-30,000.
  7. Release trip odometer button and switch ignition off.

Inspection system Opel Corsa D. In order to guarantee economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals.
If the service interval remaining distance is less than 1500 km, InSP is displayed with a remaining distance of 1000 km when the ignition is switched on and off. If less than 1000 km remains, InSP is displayed for several seconds. Have the next service performed by a workshop within one week or 500 km (whichever occurs first).

Reset the Oil Life on My Suzuki XL7

Leave a reply

How do you reset maintenance light, reset service light indicator Suzuki XL7. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Suzuki XL7, oil reset instructions:

Instructions

1.Sit in the driver’s seat of the XL7. Insert the ignition key and turn it to “RUN.” Do not start the engine.

2.Press and release the gas pedal three times within five seconds. Watch for the engine oil light to flash, indicating that the system is reset.

3.Turn the key to “OFF” and remove it from the ignition.

Turn Off an Oil Light on a 2005 KIA Spectra

Leave a reply

Instructions

1. Pull the vehicle over to a safe area, if the light comes on while driving. If you are very close to a store that sells motor oil, stop there. Do not continue driving with the indicator light lit, as severe engine damage may occur.

2. Turn off the vehicle’s engine and open the hood. Locate the oil filler cap and oil dipstick on the top-front of the engine.

3. Check the engine oil level on the oil dipstick. If the engine oil is low, remove the oil cap and add oil until the oil level on the oil dipstick reaches the “Full” mark.

4. Replace the oil cap and restart the Kia. The oil light should turn off within a few seconds of starting the vehicle.

Reset the Range Rover Airbag Fault Code

Leave a reply

Instructions

1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.

2. Slide the clamp off of the negative battery terminal.

3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.

4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.

Reset the Service Lights on a BMW 1-Series

Leave a reply

Reset service light indicator, engine oil life BMW 1-Series reset instructions:

Many models in the BMW 1-series are equipped with a maintenance system that monitors driving conditions to calculate when regular maintenance should be completed. When the computer determines it is time for regular service, a reminder light is illuminated on the control panel. After the scheduled service is performed, the service lights should be reset in order for the computer to accurately track when the next service will be due.

Instructions

1. Insert the key into the ignition.

2. Press the “Start/Stop” button. Wait for the service reminder lights to turn on and off.

3. Press and hold the trip odometer “Reset” button.

4. Release the “Reset” button when the service menu appears.

5. Press the “Menu” button on the end of the turn signal arm to move through the menu until the service reset option is highlighted.

6. Press and hold the “Reset” button until the service light resets.