Tag Archives: reset procedure

Reset enhanced accident response system Fiat 500

Leave a reply

Reset enhanced accident response system Fiat 500. From year: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset enhanced accident response system Fiat 500.

In the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of theevent, the ORC will determine whether to have the Enhanced Accident Response System perform the following functions:

  • Cut off fuel to the engine.
  • Flash hazard lights as long as the battery has power or until the ignition key is turned off.
  • Turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed.
  • Unlock the doors automatically.
  • After the event occurs, when the system is active, the message Fuel Cutoff See Handbook is displayed. Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.

System reset procedure.

After an impact causing air bag deployment, the left and right turn signal lights, located in the instrument panel cluster, will both be blinking, until the ignition is turned off. In order to move your vehicle to the side of the road you must follow the system reset procedure.

  1. Turn ignition OFF. Turn signal switch must be placed in neutral state.
  2. Turn ignition ON. Customer will see left turn light is OFF. Right turn light blinks.
  3. Turn right turn signal switch ON. Customer will see – right turn light is ON solid. Left turn light blinks.
  4. Turn left turn signal switch ON. Customer will see, left turn light is ON solid. Right turn light blinks.
  5. Turn right turn signal switch ON. Customer will see, right turn light is ON solid. Left turn light blinks.
  6. Turn left turn signal switch ON. Customer will see, Left turn light is ON solid. Right turn light is ON solid.
  7. Turn left turn signal switch OFF. Turn signal switch must be placed in neutral state. Customer will see, left turn light is OFF. Right turn light is OFF.
  8. Turn ignition OFF. Customer will see, system is now reset and the engine may be started.
  9. Turn hazard flashers OFF (manually).
  10. If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful.

If a deployment occurs.

The advanced front Air Bags are designed to deflate immediately after deployment.

Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system.

If you do have a collision which deploys the air bags, any or all of the following may occur:

  • The nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately.
  • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose orthroat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning.

Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you.

Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well.

Oil reset service light indicator Land Rover Discovery 3

Leave a reply

Reset service light indicator Land Rover Discovery 3. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

Reset service light indicator Land Rover Discovery 3.

Procedure to check/reset service status, distance counter on a Land Rover Discovery 3.

  1. Switch ignition OFF.
  2. Press and Hold left instrument panel reset button, switch ignition ON to position I (accessories).
  3. Keep reset button pressed for approximately 5 seconds until the LCD displays RESET SIA.
  4. The distance to service (e.g. 2150 miles) and the service type (e.g. Inspection/oil service) will be displayed.
  5. Has the Reset Distance limit been reached or exceeded? o NO.
  6. Follow instructions in section 2 below o YES Follow Reset Distance Counter instructions below Reset Distance counter procedure.
  7. Press and hold left instrument reset button for 5 seconds. RESET will begin to flash on the LCD display.
  8. To reset distance the left hand button should be pressed before the RESET message has flashed 5 times. The LCD will display END SIA. Switch ignition off.

Procedure to check/reset service status date counter on a Land Rover Discovery 3.

  1. Press left instrument panel reset button once.
  2. The LCD will display RESET SIA followed by the service due date.
  3. Has the Reset Date limit been reached or exceeded? o NO.
  4. Press the left instrument button once.
  5. The LCD will display END SIA to indicate the service interval check/reset procedure has been cancelled. o YES, Follow Reset Date Counter instructions below Reset Date counter procedure.
  6. Press and hold left instrument reset button for 5 seconds.
  7. RESET will begin to flash on the LCD display.
  8. To reset distance the left hand button should be pressed before the RESET message has flashed 5 times.
  9. The LCD will display END SIA. Switch ignition off.

oil-reset-service-light-indicator-Land-Rover-Discovery-3

Service Light Reset SCION xD

Leave a reply

2007-2011

1. Turn the ignition to run (one position before starting engine).
2. Select trip metre A reading by using the trip metre button and then turn the ignition off.
3. While pressing the trip meter reset button
4. Continue to press and hold the button until the trip meter displays “”000000″”.”
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

2012

1. Turn the ignition to run (one position before starting engine).
2. Press the MODE switch knob on the upper right side of the combination meter until “”TRIP A”” is shown and then turn the ignition off.”
3. While pressing the trip meter reset button
4. After the reset procedure is complete
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Alero

Leave a reply

1999-2003

Turn the ignition to run (one position before starting engine).
Push the RESET button located in the drivers instrument panel fuse block. The CHANGE OIL light will start to flash.
Press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2004

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the chimes sound and the CHANGE OIL lamp goes out. If the lamp stays on and and no chime is heard, repeat the reset procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Land Rover Range Rover

Leave a reply

2005-2009

Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.