1. Turn the ignition to run (one position before starting engine).
2. Ensure odometer reading is shown, turn ignition off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000″ and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
Reset service interval display, insp and oil service for Volvo XC90, 2006, that can be made manually by use button on car dashboard.
Reset service light indicator, engine oil life Volvo XC90, oil reset instructions:
“Resetting the service reminder indicator (SRI), model years 2002-
The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120s each time the ignition is switched on.
Proceed as follows to reset the service reminder indicator (SRI):
1.Ignition position I
2. Press and hold in the reset button for the trip odometer
3. Ignition position II. Note! Turn the key to position II within 2 seconds
4. Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released
5. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded
6. If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds.
Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.”
Reset service light indicator, engine oil life BMW 525i reset instructions:
The good news is you can do it yourself as i explained to the car owner.
Here is how:
With the ignition off.
Press and Hold the trip meter button,
keep held in and turn ignition to position 1 this is the first click the one before the ignition lights come on
Keep the button pressed in for about 5 seconds until you see “Oil Service” or “Inspection” with “Reset” or “Re” in the display.
(On vehicles with “High” cluster, you will also see the amount of fuel in litres remaining until next service).
Quikly release and Press the button again now hold for a further 5 seconds or until “Reset” or “Re” flashes.
While this display is flashing,quickly release and press the button again to reset the Service Interval.
After the display has shown the new service interval you should see END SIA” for about 2 secs.
Please note this procedure should only be used after you car has been serviced and i would qeustion any company who is unable to reset the
service/oil light either using diagnostic equipment or using this method after they have have serviced a vehicle.
Reset service light indicator, engine oil life Citroen Xsara Picasso reset instructions:
How to Reset the Service Light Citroen Xsara Picasso
Recently I have had a few requests for Citroen Xsara Picasso Service Light Reset information from people who service their own vehicles.
Being a mobile mechanic and auto diagnostic specialist I could use the stock answer and say “I’ll have to plug it in for you”.
As you have no doubt seen through my other posts I do not believe in making things difficult for the home mechanic.
Here is the procedure:
Sit in drivers seat ignition off and handbrake applied.
Press and hold trip reset button.
Turn key to position two (ignition lights on engine not started).
Keeping the trip reset button pressed in you will notice your trip meter counting down.
When zero (0) is reached start the car and the service light (spanner symbol) should now be extinguished.
Please only use this information after your vehicle has been serviced
2005-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates for 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.
1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.