Tag Archives: knob

Oil service light indicator reset an Audi S8 Service Interval

Reset service light indicator, engine oil life Audi S8, oil reset instructions:

Instructions:

  1. Locate the trip-meter knob in the lower center of the gauge cluster. The knob is black and you use it to reset your mileage on your tip-meter.
  2. Push inward on the knob until the service interval light starts to flash. This generally takes about 10 seconds.
  3. Let the knob out, and then tap it in one time quickly to turn off the light.

You can expect the Audi S8 service interval light to come on every 3,000 miles when it is time to change the oil in your vehicle. You can also expect it to come on every 15,000 miles for a regular maintenance check. If you usually take your Audi to the dealership to have it serviced, they will turn the light off for you. However, if you want to save money and do the work yourself, you need to know how to turn off the service interval light yourself.

Reset odometer and two trip meters Toyota Land Cruiser 100 series

How to reset odometer and two trip meters Toyota Land Cruiser 100 series.

Reset odometer and two trip meters Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

Reset-odometer-and-two-trip-meters-Toyota-Land-Cruiser-100-series

 

 

 

 

 

 

 

This meter displays the odometer and two trip meters.

  1. Odometer-Shows the total distance the vehicle has been driven.
  2. Two trip meters-Show two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the fuel economy and the other to measure the distance on each trip. All trip meter data is cancelled if the electrical power source is disconnected.
  3. Trip meter reset knob-Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push. To reset the trip meter A to zero, display the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

All information how to reset odometer and two trip meters is taken from Toyota Land Cruiser 100 series owners manual.

Reset oil service light indicator Toyota Tundra second generation

Reset oil service light indicator, engine oil life Toyota Tundra 2. From year: 2005-2014 reset instructions:

How to reset oil service light Toyota Tundra 2 generation.

This light acts as a reminder when to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500 miles) after the engine oil replacement, this light illuminates for about 3 seconds and then flashes for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the distance driven exceeds 8000 km (5000 miles), the light will come on after the ignition key is turned to “ON” position. The light will remain on thereafter. If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. If the light comes on, replace it as soon as possible.

The system must be reset after the engine oil replacement. Reset the system by the following procedure:

When tje Maint Requd appears on a Toyota Tundra you must follow this steps to reset the warning light.

1. Turn the ignition key to the “ACC” or “LOCK” position with the odometer reading shown.
2. Turn the ignition key to the “ON” position while holding down the trip meter reset knob. See below pictures.
3. On dash will appear ” – – – – – – ” who will blink.
4. Hold down the knob for at least 5 seconds. The odometer indicates “000000” and the light goes off.
5. If the system fails to reset, the light will continue flashing.

All information how can you reset oil service light is taken from Toyota Tundra second generation owners manual.

Service oil reset Toyota Venza 2011 – 2013

How do you reset service light indicator Toyota Venza Year 2011, 2012, 2013

1. Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
2. Turn the “ENGINE START STOP” switch off.
3. While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
4. Continue to press and hold the button until the trip meter displays “000000”.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil Service Light Reset Audi TT

Reset service light indicator, engine oil life Audi TT, year 2000-2004 oil reset instructions:

2000-2004
*Diagnostic Reset Tool Required

Manual Reset using DIS and Reset Knobs:

1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition – do not start the engine.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.

Manual Reset for 2000 only:

1. Turn off the ignition.
2. Press and hold the TRIP RECORDER reset button on the instrument cluster and turn on the ignition.
3. Release the button. The display will show SERVICE IN —MI or SERVICE.
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2005-2007
1. Turn off the ignition.
2. Press and hold the button to the right of the LCD display in the instrument cluster.
3.Turn the ignition on (do not start the engine); the message “”SERVICE”” appears. Release button.”
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.

2008-2012
“Audi recommends the use of a reset tool. *Depening on model