1. switch ignition OFF,
2. press & hold trip reset stalk (instrument cluster)
3. Switch ignition ON
4. keep pressed for 10 secs,
Display will now read 0 and ‘spanner’ symbol will go out
Toyota 4Runner 2003-onwards
With the ignition “OFF”, press and hold “RESET” button. Turn ignition to the “ON” position. Continue to hold button until “MAINT REQD” light turns off.
Turn ignition off.
Camry 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Corolla
Turn the key to the off position. Press and hold down the trip meter button and turn the key to the “on” position. Continue to hold the trip button for 5 seconds after the key is turned on, then release.
Highlander 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Matrix 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Prius 2004-onwards
With the “POWER” switch off, press and hold “ODO TRIP” button. Press “POWER” switch twice selecting “IG-ON”. Continue to hold button until”000000″ is displayed and “MAINT REQD” light turns off. Turn “POWER” switch to off.
RAV4 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sequoia 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sienna 2004-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Solara 2004-onwards
With the ignition “OFF”, press and hold button to the left of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tacoma 2005-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tundra 2003-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
1. Turn Igniton off
2. With ignition ‘OFF’ press and hold both arrow buttons, turn ignition on.
3. Release buttons after 3 seconds – the reset reminder should be flashing.
4. Press and hold set button for approx 3 seconds or until beep.
5. If you need to reset oil service – Press and hold set button again for approx 3 seconds or until beep. ‘Service Reset No Items’ should show.
Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.
Instructions
1.Turn the ignition switch to the “ON” position. Do not start the engine.
2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.
3.Turn the ignition switch to the “OFF” position.
4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.
Engine Oil Change Indicator System
Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.
1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three times
within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.