Tag Archives: repeat

Oil service reset Alero

Leave a reply

1999-2003

Turn the ignition to run (one position before starting engine).
Push the RESET button located in the drivers instrument panel fuse block. The CHANGE OIL light will start to flash.
Press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2004

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the chimes sound and the CHANGE OIL lamp goes out. If the lamp stays on and and no chime is heard, repeat the reset procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil light reset Jeep Renegade Concept

Leave a reply

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.

Oil service reset Jeep Commander

Leave a reply

Engine Oil Change Indicator System

Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.

1. Turn the ignition switch to the ON position (Do not
start the engine).

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Reset the service oil light on Saab 9-7x

Leave a reply

Reset service light indicator, engine oil life Saab 9-7x, year 2005-2009 reset instructions:

2005-2009
Turn the ignition to run (one position before starting engine).
Use the fuel button on the Driver Information Center to reach the ENGINE OIL LIFE screen.
Press and hold the select button on the DIC for 5 seconds while ENGINE OIL LIFE is displayed.
OIL LIFE RESET will appear on the DIC display for 10 seconds to let you know the system is reset. If the change oil light comes back on when you start your vehicle, the engine oil life system has not reset, repeat the procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Nissan Z

Leave a reply

2006-2008
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.