Tag Archives: vehicles

Reset the oil service light indicator for a Volkswagen Eos 2013

How do you reset service light indicator Volkswagen EOS year 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013

1. Turn the ignition off.
2. Press and hold the 0,0 button (located to the right of the instrument cluster).
3. Turn the igntion on (do not start the engine) and release the 0,0 button. Briefly press the double square button (located to the left of the instrument cluster).
4. Turn the ignition off and then start the engine to verify the indicator has been reset.
or
2. Use the rocker switch on the windshield wiper lever to select “Settings” and confirm with button underneath windshield wiper lever then follow steps 4-5.
or
3. Use the buttons on the right hand side of the multi function steering wheel
4. Select the “Settings” menu followed by the “Service” submenu. Select “Reset” and confirm.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
*vehicles equipped with a navigation system can also access the reset menu from the SETTINGS button.

Reset tire pressure warning light Toyota Rav4 XA40

Reset tire pressure warning light Toyota Rav4 XA40 fourth generation. From year: 2013, 2014.

How to reset oil service light Toyota Rav4, 3 generation XA30, 4 generation.

How to initialize the tire pressure warning system.

  1. Park the vehicle in a safe place and turn the engine switch to the “LOCK” position (vehicles without a smart key system) or off (vehicles with a smart key system). Initialization cannot be performed while the vehicle is moving.
  2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the engine switch to the “ON” position (vehicles without a smart key system) or IGNITION ON mode (vehicles with a smart key system).
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.
  5. Reset-tire-pressure-warning-light-Toyota-Rav4-XA40
  6. Vehicles without a smart key system: Wait for a few minutes with the engine switch in the “ON” position and then turn the engine switch to the “ACC” or “LOCK” position. Vehicles with a smart key system: Wait for a few minutes with the engine switch in IGNITION ON mode and then turn the engine switch off.

Registering ID codes Toyota Rav 4.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.

When to replace your vehicle’s tires. Tires should be replaced if:

  • You have tire damage such as cuts, splits, cracks deep enough to expose the fabric, and bulges indicating internal damage.
  • A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.

If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels (vehicles with the tire pressure warning system).

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life Toyota Rav4.

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

Routine tire inflation pressure checks (vehicles with the tire pressure warning system).

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

Situations in which the tire pressure warning system may not operate properly (if equipped).

In the following cases, the tire pressure warning system may not operate properly.

  • If non-genuine Toyota wheels are used.
  • A tire has been replaced with a tire that is not an OE (Original Equipment) tire.
  • A tire has been replaced with a tire that is not of the specified size.
  • Tire chains etc. are equipped.
  • Lock nuts are equipped.
  • An auxiliary-supported run-flat tire is equipped.
  • If a window tint that affects the radio wave signals is installed.
  • If there is a lot of snow or ice on the vehicle, particularly around the wheels or wheel housings.
  • If the tire inflation pressure is extremely higher than the specified level.
  • If the spare tire is in a location subject to poor radio wave signal reception.
  • If a large metallic object which can interfere with signal reception is put in

*: Vehicles with a full-size spare tire only

Performance may be affected in the following situations.

  • Near a TV tower, electric power plant, gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise.
  • When carrying a portable radio, cellular phone, cordless phone or other wireless communication device.

When the vehicle is parked, the time taken for the warning to start or go off could be extended.
When tire inflation pressure declines rapidly for example when a tire has burst, the warning may not function.

Oil service light reset indicator Chevrolet Renault Twingo 2007

How do you reset maintenance light, reset service light indicator Renault Twingo 2007. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Renault Twingo, oil reset instructions:

How to reset oil service light Renault Twingo. From year: 2007

The service light on these vehicles is usually a spanner / wrench symbol. To reset that indicator:

Turn the Ignition ON (position 2) but do not start the engine

(On cars with keycard ignition, insert the card, then press and hold the start button for 5 seconds to turn on the dash cluster)

Press the button on the end of the wiper stalk repeatedly until the spanner symbol and miles to service appears on the display

(Some models have 2 buttons, which cycle through the options in opposite directions – either button can be used in this case)

Press and hold the button

The display will now change to the new service interval and start flashing

Keep holding the button until the display stops flashing

Release the button

Reset the oil service light 2011 Ford Fiesta

To reset the oil service light, use the following procedure:

1. With the ignition in the off position, press the brake and accelerator pedals.
2. For keyed vehicles, turn the key to the accessory position; for pushbutton start vehicles, press the Start/Stop button once quickly. Do not start the engine.
3. Press the accelerator and brake pedals fully for 20 seconds.
4. “Engine Oil Change Due Next Service” and the oil service light will display.
5. Turn the vehicle off. The message and lights will be cleared.

Normal Maintenance

Under what Ford terms “normal” conditions, oil changes will occur at a maximum of every 10,000 miles (16,000 kilometers) or 12 months. Other services to be performed at every oil change include:
• Rotate tires.
• Inspect wheels and related components for noise, wear, looseness or drag.
• Inspect brake pads, shoes, rotors, drums, brake linings, hoses and parking brake.
• Inspect engine cooling system for strength; inspect cooling system hoses.
• Inspect exhaust system and heat shields.
• Inspect half-shaft boots.
• Inspect and lubricate steering linkage, ball joints, suspension, tie-rod ends and U-joints if equipped with grease fittings.
• Inspect cabin air filter (if equipped).

Service light reset Renault Clio, Laguna 2

Service light reset Renault Clio (2005-present), Espace 4 (2003-present), Laguna II (2001-2007), Megane II (2002-2009), Scenic II (2003-2009), Twingo (2007-present), Vel Satis (2002-2009)

The service light on these vehicles is usually a spanner / wrench symbol. To reset that indicator:

Turn the Ignition ON (position 2) but do not start the engine
(On cars with keycard ignition, insert the card, then press and hold the start button for 5 seconds to turn on the dash cluster)
Press the button on the end of the wiper stalk repeatedly until the spanner symbol and miles to service appears on the display
(Some models have 2 buttons, which cycle through the options in opposite directions – either button can be used in this case)
Press and hold the button
The display will now change to the new service interval and start flashing
Keep holding the button until the display stops flashing
Release the button