Tag Archives: key

Reset tire pressure warning light Toyota Solara 2 generation

Leave a reply

Reset tire pressure warning light Toyota Solara 2 generation. From year: 2004, 2005, 2006, 2007, 2008.

How to reset tire pressure warning light Toyota Solara second generation.

Reset-tire-pressure-warning-light-Toyota-Solara-2-generation

This light warns that the tire pressure of one or more of your tires (including ground spare tire) is low. The light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is functioning properly. If the warning light comes on, stop your vehicle in a safe place as soon as possible and check that the inflation pressure of all tires (including ground spare tire) is as specified on the tire and loading information label.

The light should go off a few minutes after the tire pressure is adjusted.

If the warning light comes on after blinking for 1 minute, the tire pressure warning system may be malfunctioning. Contact your Toyota dealer.

TIRE PRESSURE WARNING RESET SWITCH.

When initializing the system, the present tire inflation pressure is stored as standard. The tire pressure warning system determines decreased air pressure by comparing the present and the standard tire inflation pressures. When you change the set tire inflation pressure, it is necessary to initialize the tire pressure warning system.

  • When changing the tire size.
  • When rotating the tire on vehicles differing with front and rear tire inflation pressure.

To initialize the system, perform the following:

  1. Park the vehicle in a safe place and turn the ignition key to “OFF” position.
  2. Adjust the pressure of all the installed tires to the specified cold tire inflation pressure level.
  3. Turn the ignition key to the “ON” position.
  4. Push and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times.
  5. Leave for a few minutes with the ignition key in “ON” position, and then turn the ignition key to “OFF” position.

If you push the tire pressure reset switch while vehicle is moving, initialization is not performed. If you push the tire pressure reset switch accidentally and initialization is performed, adjust the tire inflation pressure to the specified level and initialize the system again.

If the tire pressure warning light does not blink slowly three times when you push and hold the reset switch, initialization has failed and the tire pressure warning system may not work properly. In this case, initialize the system again. If initialization cannot be performed, have the system checked at your Toyota dealer.

Do not push the reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

That it is the full procedure how to reset tire pressure warning light Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

Reset VSC warning light Toyota Solara second generation

Leave a reply

Reset VSC warning light Toyota Solara second generation. From year: 2004, 2005, 2006, 2007, 2008.

How to reset VSC warning light Toyota Solara 2 generation.

The light warns that there is a problem somewhere in the vehicle stability control system or traction control system. The light will come on when the ignition key is turned to “ON”, and will go off after about a few seconds.

If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.

All information how can you reset VSC warning light is taken from Toyota Solara second generation owners manual.

That it is the full procedure how to reset VSC warning light Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

Reset oil service light Toyota Tacoma second generation

Leave a reply

Reset oil service light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset maint reqd service light Toyota Tacoma 2 generation.

Reset-oil-service-light-Toyota-Tacoma-second-generation.

Engine Oil Replacement Reminder Light (for vehicles sold in U.S.A.).

This light acts as a reminder to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500 miles) after the engine oil replacement, this light illuminates for about 3 seconds and then flashes for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the distance driven exceeds 8000 km (5000 miles), the light will come on after the ignition key is turned to “ON” position. The light will remain on thereafter.

If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. If the light comes on, replace it as soon as possible. The system must be reset after the engine oil replacement. Reset the system by the following procedure:

  1. Turn the ignition key to the “OFF” position with the odometer reading shown. For details, see “Odometer and two trip meters” in this category.
  2. Turn the ignition key to the “ON” position while holding down the trip meter reset knob. See below picture.
  3. How-to-reset-maint-reqd-service-light-Toyota-Tacoma-2-generation.
  4. Hold down the knob for at least 5 seconds. The odometer indicates “000000” and the light goes off.

If the system fails to reset, the light will continue flashing.

All information how can you reset oil service light is taken from Toyota Tacoma second generation owners manual.

 

That it is the full procedure how to reset oil service light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset brake system service light Toyota Tacoma second generation

Leave a reply

Reset brake system service light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset brake system service light Toyota Tacoma 2 generation.

This light comes on in the following cases when the ignition key is in the “ON” position.

When the parking brake is applied.

This light comes on for a few seconds when the ignition key is turned to the “ON” position even after the parking brake is released.

When the brake fluid level is low.

It is dangerous to continue driving normally when the brake fluid level is low.

When the hydraulic brake booster fails (with the vehicle stability control system).

If the hydraulic booster causes a problem resulting in poor braking performance, the warning light comes on and buzzer sounds continuously.

Have your vehicle checked at your Toyota dealer in the following case:

  • The light does not come on even if the parking brake is applied when the ignition key is in the “ON” position.
  • The light does not come on even if the ignition key is turned on with the parking brake released.

A warning light turning on briefly during operation does not indicate a problem.

Without the vehicle stability control system.

If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.
  • The brake system warning light re mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

With the vehicle stability control system.

If any of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running.
  • The warning buzzer comes on together with the warning light. In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.
  • The brake system warning light remains on together with the “ABS” warning light.
  • In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

With the vehicle stability control system.

Any of the following conditions may occur, but do not indicate the malfunction:

  • The light may stay on for about 60 seconds after the ignition key is turned to the “ON” position. It is normal if it turns off after a while.
  •  Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the light turns off and the buzzer stops sounding after a few seconds.
  •  You may hear a small sound in the engine compartment after the engine is started or the brake pedal is depressed repeatedly. This is a pump pulsating sound of the brake system, and it is not a malfunction.

All information how can you reset brake system service light is taken from Toyota Tacoma second generation owners manual.

That it is the full procedure how to reset brake system service light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset seat belt reminder light Toyota Tacoma second generation

Leave a reply

Reset seat belt reminder light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset seat belt reminder light Toyota Tacoma 2 generation.

Driver’s seat belt reminder light and buzzer.

The light and buzzer act as a reminder to buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light continues flashing and the buzzer stops after about 4 to 8 seconds.

Front passenger’s seat belt reminder light.

The light acts as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light may flash.

All information how can you reset seat belt reminder light is taken from Toyota Tacoma second generation owners manual.

That it is the full procedure how to reset seat belt reminder light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.