Reset odometer and two trip meters Toyota Land Cruiser 100 series

Leave a reply

How to reset odometer and two trip meters Toyota Land Cruiser 100 series.

Reset odometer and two trip meters Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

Reset-odometer-and-two-trip-meters-Toyota-Land-Cruiser-100-series

 

 

 

 

 

 

 

This meter displays the odometer and two trip meters.

  1. Odometer-Shows the total distance the vehicle has been driven.
  2. Two trip meters-Show two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the fuel economy and the other to measure the distance on each trip. All trip meter data is cancelled if the electrical power source is disconnected.
  3. Trip meter reset knob-Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push. To reset the trip meter A to zero, display the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

All information how to reset odometer and two trip meters is taken from Toyota Land Cruiser 100 series owners manual.

Reset brake system warning light Toyota Land Cruiser 100 series

Leave a reply

How to reset brake system warning light Toyota Land Cruiser 100 series.

Reset brake system warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light comes on in the following cases when the ignition key is in the “ON” position.

When the parking brake is applied.

This light comes on for a few seconds when the ignition key is in the “ON” position even after the parking brake is released.

When the brake fluid level is low.

It is dangerous to continue driving normally when the brake fluid level is low.

When the hydraulic brake booster fails.

If the hydraulic booster causes an problem resulting in poor braking performance, the warning light comes on and buzzer sounds continuously.

Have your vehicle checked at your Toyota dealer in the following cases:

The light does not come on even if the parking brake is applied when the ignition key is in the “ON” position.
The light does not come on even if the ignition key is turned on with the parking brake released.
A warning light turning on briefly during operation does not indicate a problem.

If any of the following conditions occur, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running.
  • The warning buzzer comes on together with the warning light.
  • In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.

The brake system warning light remains on together with the “ABS” warning light.

In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

Any of the following conditions may occur, but do not indicate a malfunction:

The light may stay on for about 60 seconds after the ignition key is turned to “ON” position. It is normal if it goes out after a while.

Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the light goes out and the buzzer stops sounding after a few seconds.

You may hear a small sound in the engine compartment after the engine is started or the brake pedal is depressed repeatedly. This is a pump pulsating sound of the brake system, and it is not a malfunction.

All information how can you reset brake system warning light is taken from Toyota Land Cruiser 100 series owners manual.

Reset tire pressure warning light Toyota FJ Cruiser

Leave a reply

How to reset tire pressure warning light Toyota FJ Cruiser.
Reset tire pressure warning light Toyota FJ Cruiser. From year: 2012, 2013, 2014.

How to initialize the tire pressure warning system.

  • Park the vehicle in safe place and turn the engine switch to the LOCK position. While the vehicle is moving, initialization is not performed.
  • Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  • Turn the engine switch to the ON position.
  • Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.

Reset-tire-pressure-warning-light-Toyota-FJ-Cruiser

  • Wait for a few minutes with the engine switch on, and then turn the engine switch to the ACC or LOCK position.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

When to replace your Toyota FJ Cruiser tires.

Tires should be replaced if:

You have tire damage such as cuts, splits, cracks deep enough to expose the fabric or bulges indicating internal damage.
A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.
If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels on your Toyota FJ Cruiser.

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life.

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

If the tread wears down below 0.16 in. (4 mm) on snow tires.

The effectiveness of snow tires is lost.

How to check service light Toyota FJ Cruiser

Leave a reply

Checking service reminder indicators on a Toyota FJ Cruiser except the low fuel level warning light.

How to check service light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

Apply the parking brake.

Open one of the side doors, back door or back window. The open door warning light should come on.
Close the door and back window. The open door warning light should go off.
Turn the ignition key to “ON”, but do not start the engine. All the service reminder indicators except the open door warning light should come on.
The following service reminder indicators go off after a few seconds:

  • Engine oil replacement reminder light.
  • ABS warning light.
  • VSC TRAC warning light.
  • AUTO LSD indicator light two−wheel drive models.
  • VSC OFF indicator light four−wheel drive models, and vehicles with rear differential lock.
  • Slip indicator light.
  • The SRS warning light goes off after about 6 seconds. There may be the case that the “ABS” warning light (brake assist system warning light), “VSC TRAC” warning light and “AUTO LSD” (two−wheel drive models), “VSC OFF” (four−wheel drive models, and vehicles with rear differential lock) or slip indicator light stay on for about 60 seconds after the ignition key is turned to the “ON” position. It is normal if they go out after a while.

If any service reminder indicator or warning buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.

All information how to check service light is taken from Toyota FJ Cruiser owners manual.

Reset front passenger’s seat belt reminder light Toyota FJ Cruiser

Leave a reply

How to reset front passenger’s seat belt reminder light Toyota FJ Cruiser.
Reset front passenger’s seat belt reminder light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

The light and buzzer act as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the driver’s seat belt is fastened. If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light may flash and buzzer to sound.

The buzzer can be set not to sound by following the procedure below.

  1. Sit on the front passenger seat.
  2. Turn the ignition key to the “OFF” position with the odometer reading shown. For details see the Odometer and two trip meters om Toyota categories.
  3. Turn the ignition key to the “ON” position.
  4. Within 6 seconds, push the trip meter reset knob and hold it for more than 10 seconds.
  5. Insert the tab of front passenger seat belt into the buckle.
  6. The odometer shows either “b−on” or “b−off”. The reading changes by pushing the trip meter reset knob and the setting of the front passenger seat belt reminder buzzer can be changed. The odometer display returns to normal if the meter reset knob has not been operated for more than 10 seconds or the ignition key is turned to the “OFF” position.

All information how can you reset front passenger’s seat belt reminder light is taken from Toyota FJ Cruiser owners manual.