Oil reset service light indicator Land Rover Discovery 3

Leave a reply

Reset service light indicator Land Rover Discovery 3. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

Reset service light indicator Land Rover Discovery 3.

Procedure to check/reset service status, distance counter on a Land Rover Discovery 3.

  1. Switch ignition OFF.
  2. Press and Hold left instrument panel reset button, switch ignition ON to position I (accessories).
  3. Keep reset button pressed for approximately 5 seconds until the LCD displays RESET SIA.
  4. The distance to service (e.g. 2150 miles) and the service type (e.g. Inspection/oil service) will be displayed.
  5. Has the Reset Distance limit been reached or exceeded? o NO.
  6. Follow instructions in section 2 below o YES Follow Reset Distance Counter instructions below Reset Distance counter procedure.
  7. Press and hold left instrument reset button for 5 seconds. RESET will begin to flash on the LCD display.
  8. To reset distance the left hand button should be pressed before the RESET message has flashed 5 times. The LCD will display END SIA. Switch ignition off.

Procedure to check/reset service status date counter on a Land Rover Discovery 3.

  1. Press left instrument panel reset button once.
  2. The LCD will display RESET SIA followed by the service due date.
  3. Has the Reset Date limit been reached or exceeded? o NO.
  4. Press the left instrument button once.
  5. The LCD will display END SIA to indicate the service interval check/reset procedure has been cancelled. o YES, Follow Reset Date Counter instructions below Reset Date counter procedure.
  6. Press and hold left instrument reset button for 5 seconds.
  7. RESET will begin to flash on the LCD display.
  8. To reset distance the left hand button should be pressed before the RESET message has flashed 5 times.
  9. The LCD will display END SIA. Switch ignition off.

oil-reset-service-light-indicator-Land-Rover-Discovery-3

Oil reset service light indicator Chevrolet Malibu

Leave a reply

How do you reset oil service light Chevrolet Malibu. From years: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012.

Reset oil service light Chevrolet Malibu.

The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation accurs where you change the oil prior to a CHANGE OIL SOON message being turned on, reset the system.

To reset oil service light on your vehicle Chevrolet Malibu follow this steps:

  • Display OIL LIFE RESET on the dash board.
  • Press and hold the INFO button & ENTER button (in the same time) buttons for at least one second.
  • OIL LIFE RESET will display.
  • Hit ENTER button again and an ACKNOWLEDGED display message will appear for three seconds.
  • This tells you the system has been reset.
  • Turn the key to LOCK/OFF.

If the CHANGE OIL SOON message comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure.

Oil reset service light indicator Chevrolet Impala

Leave a reply

How do you reset oil service light Chevrolet Impala. From years: 1999 – 2012.

Reset oil service light Chevrolet Impala. From years: 1999, 2000, 2001, 2002, 2003, 2004, 2005.

The GM Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHNAGE ENGINE OIL message being turned on, reset the system.

After changing the engine oil, the system must be reset.

To reset the CHANGE ENGINE OIL message use one of the folloqing procedures.

Reset oil service light Chevrolet Impala, using the radio. From years: 1999, 2000, 2001, 2002, 2003, 2004, 2005.

  • Turn the ignition to ACC or ON, with the radio off.
  • Press and hold the TUNE DISP knob on the radio for at least five seconds until SETTINGS is displayed.
  • Press the SEEK PSCAN up or down arrow to scroll through the main menu.
  • Scroll until OIL LIFE appears on the display.
  • Press the 1 PREV or 2 NEXT buttons to enter the submenu. Reset will be displayed.
  • Press the TUNE DISP knob to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second.
  • Once the indicator has been reset, scroll until EXIT appears on the display.
  • Press the TUNE DISP knob to exit programming. A chime will be heard to verify the exit.
  • Turn the key to OFF.
  • If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Reset oil service light Chevrolet Impala, using the accelerator pedal. From years: 1999, 2000, 2001, 2002, 2003, 2004, 2005.

  • Turn the ignition to ON, with the engine off.
  • Fully press and release the accelerator pedal slowly three times within five seconds. If the CHANGE ENGINE OIL message flashes, the system is reset.
  • However, if it stays on, it did not reset. Repeat the procedure.
  • Turn the key to OFF.
  • If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

All information is taken from the Chevrolet Impala manual.

How to reset oil service light Chevrolet Impala. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.

How to Reset the Engine Oil Life System Chevrolet Impala.

The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you
change your oil prior to a CHANGE ENGINE OIL SOON message being turned on, reset the system.

Always reset the engine oil life to 100% after every oil change. It will not reset itself. To reset the Engine Oil Life System for Chevrolet impala, do the following:

  • Display the OIL LIFE REMAINING on the DIC.
  • Press and hold the SET/RESET button on the DIC for more than five seconds. The oil life will change to 100%.
  • If the CHANGE ENGINE OIL SOON message comes back on when you start your vehicle, the Engine Oil Life System has not reset. Repeat the procedure.

All information is taken from the Chevrolet Impala manual.

Reset oil service light Cadillac Allante

Leave a reply

How do you reset oil service light Cadillac Allante. From years: 1989, 1990, 1991, 1992, 1993.

Reset oil service light Cadillac Allante. From years: 1989, 1990, 1991, 1992, 1993.

  • Turn the ignition to run (one position before starting engine).
  • Press the range button until the OIL LIFE INDEX is displayed.
  • Press and hold the AVERAGE SPEED and RANGE buttons until the display resets to 100.
  • Turn the ignition to off and start engine to verify the indicator has been reset.

Reset rear light failure Saab 9-3

Leave a reply

How to reset rear light failure Saab 9-3 first generation.

Reset rear light failure Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.

  1. Enter the key in the ignition and turn it until the lights on the dashboard go on, one position befor you start the car.
  2. The rear light failure indicator light cannot be removed by pressing CLEAR button.
  3. To reset the light push the brake pedal to clear.

CHECK messages on a Saab 9-3 first generation. When the engine is started, CHECKING will appear on the display for about 4 seconds, while the SID checks are being performed. When a CHECK indicator is generated while the vehicle is being driven, a chime will sound, INFO DISPL will illuminate on the main instrument panel, and the message will appear on the SID. The number of messages that can be displayed by the SID varies with the specification of the car. If more than one CHECK indicator has been generated, the + symbol will appear to the left of the text on the display. The indicator appear in order of priority. If a new fault occurs while another message is being displayed, the message relating to the new one will appear for 10 seconds, after which the display will return to the earlier one. Press CLR once to acknowledge a message, hereupon it will be cleared from the display. It will not be displayed again before the ignition has been switched off and then on again.