Oil reset service light Mitsubishi Lancer Evolution X

Leave a reply

How to reset oil service light Mitsubishi Lancer Evolution X.

Reset oil service light Mitsubishi Lancer Evolution X. From years: 2008, 2009, 2010.

  1. The “- – -” display can be reset while the ignition switch is “OFF”. When the display is reset, the time until the next periodic inspection is displayed and “PERIODIC INSPECTION” is no longer displayed when the ignition is switched from “OFF” to “ON”.
  2. Lightly press the multi-information meter switch until the information screen switches to service reminder display screen.
  3. Press and hold the multi-information meter switch for about 2 seconds or more to display the (wrench icon) and make it flash.
  4. Lightly press the multi-information meter switch while the icon is flashing to change the display from “- – – ” to “CLEAR”. After this, the time until the next periodic inspection will be displayed.
  5. Start the engine to verify the indicator has been reset.

Oil reset service light Mitsubishi Lancer Evolution 10

Leave a reply

How to reset oil service light Mitsubishi Lancer Evolution 10.

Reset oil service light Mitsubishi Lancer Evolution 10. From years: 2008, 2009, 2010.

  1. The “- – – -” display can be reset while the ignition switch is “OFF”. When the display is reset, the time until the next periodic inspection is displayed and “PERIODIC INSPECTION” is no longer displayed when the ignition is switched from “OFF” to “ON”.
  2. Lightly press the multi-information meter switch until the information screen switches to service reminder display screen.
  3. Press and hold the multi-information meter switch for about 2 seconds or more to display the (wrench icon) and make it flash.
  4. Lightly press the multi-information meter switch while the icon is flashing to change the display from “- – – – ” to “CLEAR”. After this, the time until the next periodic inspection will be displayed.
  5. Start the engine to verify the indicator has been reset.

Reset light airbag fault code Range Rover

Leave a reply

How to reset airbag fault code Range Rover.

Reset airbag fault code Range Rover. How to reset the Range Rover Airbag Fault Code warning light. Reset AIRBAG FAULT error message on dash board on a Range Rover.

Instructions:

  1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.
  2. Slide the clamp off of the negative battery terminal.
  3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.
  4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.

Oil reset service light indicator Range Rover Sport

Leave a reply

How do you reset service light indicator Range Rover Sport. From year: 2007.

Reset service light indicator Range Rover Sport. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

Instructions:

  1. Turn off the cars ignition.
  2. Hold down the reset button on the dash board to zero the mileage. keep it held in.
  3. Turn the cars ignition on, but do not start. Keep the button in for 5 seconds.
  4. A menu will come up, like date/mileage.
  5. Let go and then press the button again.
  6. It will toggle through some options, then get to rst.
  7. Press the button again, and your done.

Oil reset service light indicator Land Rover Freelander 2

Leave a reply

How do you reset service light indicator Land Rover Freelander 2.
Reset service light indicator Land Rover Freelander 2. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

Instructions:

  1. Hold the milage reset button in.
  2. Turn the ignition on to position 2.
  3. Keep the button held in and various different words will flash up on the little screen.
  4. Dont release until it goes back to reading the milage.
  5. Once this comes up release the button and it should be ok when you next cycle the ignition.