Toyota Land Cruiser 200 series reset tire pressure warning light

Leave a reply

How to reset tire pressure warning system Toyota Land Cruiser 200 series.

Reset tire pressure warning light Toyota Land Cruiser 200 series. From year: 2008, 2009, 2010, 2011, 2012, 2013, 2014.

  1. Park the vehicle in safe place and turn the “ENGINE START STOP” switch to OFF mode. While the vehicle is moving, initialization is not performed.
  2. While the vehicle is moving, initialization is not performed. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the “ENGINE START STOP” switch to IGNITION ON mode.
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times and the message “TIRE PRESSURE RESET PROCEEDING” appears on the multi-information display.
  5. Wait for a few minutes with the IGNITION ON mode, and then turn the “ENGINE START STOP” switch to OFF mode.
  6. The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

If you press the tire pressure reset switch accidentally.

If initialization is performed, adjust the tire inflation pressure to the specified level and initialize the tire pressure warning system again.

When the initialization of the tire pressure warning system has failed.

Initialization can be completed in a few minutes. However, in the following cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer.

When operating the tire pressure warning reset switch, the warning light does not flash 3 times and the setting message does not appear on the multi-information display.

Maintenance Oil Light Reset Honda Accord 2014

Leave a reply

How do you reset maintenance light, reset service light indicator Honda Accord, year 2013, 2014. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Honda Accord, oil reset instructions:

  1. Turn the ignition on (do not start the engine).
  2. Display the engine oil life by repeatedly pressing the SELECT/RESET button.
  3. Press and hold the SELECT/RESET knob for more than 10 seconds. The engine oil life indicator and the maintenance item codes blink.
  4. Press the SELECT/RESET knob for 5 seconds or more. The displayed maintenance item codes disappear, and the engine oil life display returns to 100%.
  5. Turn the ignition off and then start the engine to verify the indicator has been reset.

For Vehicles Equipped with MID:

  1. Turn the ignition on (do not start the engine).
  2. Press the UP/DOWN buttons on the lower right of the steering wheel to select VEHICLE SETTINGS, then press the SEL/RESET button.
  3. Press the UP/DOWN buttons until MAINTENANCE RESET appears on the display, then press the SEL/RESET button. The oil life reset mode is displayed on the MID.
  4. Select RESET with the UP/DOWN buttons, then press the SEL/RESET button. The displayed maintenance items disappear and the oil life is reset to 100%.
  5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Land Cruiser reset automatic transmission fluid temperature light

Leave a reply

How to reset automatic transmission fluid temperature indicator light Toyota Land Cruiser.

Reset automatic transmission fluid temperature warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light warns that the automatic transmission fluid temperature is too high. If this light comes on while you are driving, slow down and pull off the road. Stop the vehicle at a safe place and put the selector lever in “P” and leave the engine idling until the light goes off. If the light goes off, you can start the vehicle again. If the light does not go off, call a Toyota dealer or qualified repair shop for assistance.

Continued driving with the warning light on may damage the automatic transmission.

Toyota Land Cruiser 100 series Reset unengaged park warning light

Leave a reply

How to reset unengaged park warning light Toyota Land Cruiser 100 series.

Reset unengaged park warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light warns that the transmission “Park” mechanism is not engaged. If the four−wheel drive control is in the “N” position while the selector lever is in the “P” position, the transmission will disengage and the wheels will not lock.

To restore the park function, shift the four−wheel drive control out of “N”, or the vehicle can move.

All information how to restore the unengaged park warning light is taken from Toyota Land Cruiser 100 series owners manual.

Oil reset service light indicator Mercedes Viano 2008

Leave a reply

How do you reset maintenance light, reset service light indicator Mercedes Viano, year 2008, 2009, 2010, 2011, 2012, 2013, 2014. For reset maintenance light and that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Mercedes Viano, oil reset instructions:

  1. Ensure ignition is switched OFF.
  2. Switch ignition ON and briefly press button[A] twice.
  3. Within 10 seconds: Switch ignition OFF.
  4. Press and hold button [A].
  5. Switch ignition ON.
  6. Continue to hold button [A].
  7. The remaining distance will be displayed.
  8. After aproximately 10 seconds a warning sound will be heard and the new remaining distance will appear in the digital display.
  9. Release button [A].

Oil reset service light indicator Mercedes Viano 2008

NOTE: The service interval indicator can be reset to a higher than normal value for use with alternative higher specification engine oils. This can only be carried out using diagnostic equipment.