Tag Archives: warning light

Reset tighten fuel filler cap message Saab 9-3

Leave a reply

How to reset tighten fuel filler cap message Saab 9-3 first generation.

Reset tighten fuel filler cap message Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.

  1. Enter the key in the ignition and turn it until the lights on the dashboard go on, one position befor you start the engine.
  2. The tighten fuel filler cap message light cannot be removed by pressing CLEAR button.
  3. To reset this warning light push the brake pedal to clear.

Refueling Saab 9-3. Ensure that you are using the correct grade of fuel, unleaded AON 87-93. For optimum performance we recommend:

  • AON 90 for 2.0 Turbo 185 hp.
  • AON 93 for 2.0 Turbo 205 hp and 2.3 Turbo Viggen.

If fuel containing a mixture of alcohol is used, the following restrictions apply: Methanol: max. 5% by volume. Ethanol: max. 10% by volume. MTBE: max. 15% by volume. The fuel filler cap is located in the right rear quarter panel. Switch off engine. Insert the fuel-pump nozzle beyond the flange on the filler pipe. Do not withdraw the nozzle while filling is in progress. Cease refuelling the first time the pump stops. Fuel-tank capacity: 17.0 US gal. (64 liters)m Screw on the filler cap and keep turning until it has clicked at least three times. Manually opening the fuel filler door, see page 131, Convertible, page 52.

The most effective way to prevent condensation forming in the tank (and thus avoid possible running problems) is to keep the tank well filled. Before the onset of freezing temperatures in winter, it may be advisable to add gasoline anti-freeze to the fuel a few times to dispel any condensation in the system.

Reset key not accepted message Saab 9-3

Leave a reply

How to reset key not accepted message Saab 9-3 first generation.

Reset key not accepted message Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.

  1. Enter the key in the ignition and turn it until the lights on the dashboard go on, one position befor you start the engine.
  2. The key not accepted message light cannot be removed by pressing CLEAR button.
  3. To reset this warning light push the brake pedal to clear.

If the your Saab 9-3 does not start. If the text “KEY NOT ACCEPTED” appears on the SID when the engine refuses to start, the trouble may be a fault in the transponder of the key or in the receiver of the ignition switch. Proceed as follows:

  1. Turn the key back to the LOCK position.
  2. Turn the key to the ON position.
  3. Press one of the buttons on the remote control (the LED on top of the dash stops flashing).
  4. Start the engine.

Reset replace key battery message Saab 9-3

Leave a reply

How to reset replace key battery message Saab 9-3 first generation.

Reset replace key battery message Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.

 

  • Enter the key in the ignition and turn it until the lights on the dashboard go on, one position befor you start the engine.
  • The replace key battery message light cannot be removed by pressing CLEAR button.
  • To reset this warning light push the brake pedal to clear.

Changing the remote-control battery. When the battery voltage in the remote control falls below a predetermined level the SID will issue the following message: REPLACE KEY BATTERY. Press the CLEAR button on the SID to acknowledge this message. You must then replace the battery without delay to avoid malfunctions. The life of the battery is 4-5 years. After changing the battery you must press the unlocking button of the remote control four times (or until the door locks cycle) while the car is within the range of the remote control in order for the control module to recognize the remote.

Battery for remote control. The battery for the remote control will normally have a life of 4-5 years. When the battery needs changing, ”REPLACE KEY BATTERY” will appear on the SID. After fitting a new battery, press the unlock button on the remote ontrol at least four times in succession, so that the car alarm can recognize the signals from the transmitter. If the remote control has been exposed to very low temperatures, it may not function properly. If this happens, warm it in your hands for a few minutes. If the remote control is not working, it may be because the code signal has not been synchronized with that in the control module for the car alarm. To rectify this, press the unlock button on the remote control at least four times in quick succession. When it is recognized, the door locks will cycle.

Toyota Land Cruiser 100 series reset SRS airbag warning light

Leave a reply

How to reset SRS airbag warning light Toyota Land Cruiser 100 series.

Reset SRS airbag warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This indicator comes on when the ignition key is turned to the “ON” position. It goes off after about 6 seconds. This means the SRS airbags and seat belt pretensioners are operating properly.

The warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensor assemblies, curtain shield airbag sensor assemblies, driver’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system and indicator light, front passenger’s seat belt buckle switch, seat belt pretensioner assemblies, inflators, roll sensing of curtain shield airbags off indicator light, interconnecting wiring and power sources.

If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible.

  • The light does not come on when the ignition key is turned to the “ON” position or remains on for more than 6 seconds or flashes.
  • The light comes on or flashes while driving.

The SRS warning light will come on and front passenger occupant classification indicator light will indicate “OFF” if there is a malfunction in the front passenger occupant classification system.
All information how to reset SRS airbag warning light is taken from Toyota Land Cruiser 100 series owners manual.

Toyota Land Cruiser 100 series reset low fuel level warning light

Leave a reply

How to reset low fuel level warning light Toyota Land Cruiser 100 series.

Reset low fuel level warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light comes on when the fuel level in the tank becomes nearly empty. To reset this light you must fill up the tank as soon as possible and the warning light will go off.

Al infromation are taken from Toyota Land Cruiser 100 series owners manual.

That it is the full procedure how to reset low fuel level warning light Toyota Land Cruiser 100 series. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.