Tag Archives: indicator

Reset low engine oil pressure warning light Toyota Tundra

Leave a reply

How to reset low engine oil pressure warning light Toyota Tundra 2 generation.

Reset low engine oil pressure warning light Toyota Tundra second generation. From year: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

This light warns that the engine oil pressure is too low.

If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance.

The light may occasionally flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly.

The light may come on when the oil level is extremely low. It is not designed to indicate low oil level, and the oil level must be checked using the level dipstick. To reset the low engine oil pressure warning light on a Toyota Tundra you must add some engine oil and the indicator will go off.

Do not drive the vehicle with the warning light on—even for one block. It may ruin the engine.

All information how to reset low engine oil pressure warning light is taken from Toyota Tundra 2 generation owners manual.

Reset malfunction indicator lamp Toyota Tundra second generation

Leave a reply

How to reset malfunction indicator lamp Toyota Tundra 2 generation.

Reset malfunction indicator lamp Toyota Tundra second generation. From year: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on, or the lamp comes on while driving, first check the followings.

Empty fuel tank. If the fuel tank is empty, refuel immediately.
Loose fuel tank cap. If the fuel tank cap is loose, securely tighten it.
These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp does not go off even after several trips, contact your Toyota dealer as soon as possible.

If the fuel tank is not empty or the fuel tank cap is not loose.

There is a problem somewhere in the engine, emission control system, electronic throttle control system, automatic transmission electrical system or warning light system itself.

Contact your Toyota dealer as soon as possible to service the vehicle. If engine speed does not increase when the accelerator pedal is depressed, there may be a problem somewhere in the electronic throttle control system. At this time, vibration may occur. However, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible. Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the ignition key is turned to “ACC” or “LOCK” position.

Be especially careful to prevent erroneous pedal operation.

Emissions Inspection and Maintenance (I/M) programs.

Your vehicle may not pass a state emission inspection if the malfunction indicator lamp remains on. Contact your Toyota dealer to check your vehicle’s emission control system and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection.

All information how can you reset malfunction indicator lamp is taken from Toyota Tundra second generation owners manual.

MAINT REQ’D Reset & Service Specifications Toyota Camry 2013

Leave a reply

MAINT REQD light can be reset by doing the following:

1. Press the “”ENGINE START STOP”” switch once (do not start the engine) or turn ignition key to run (one position before starting the engine).
2. Ensure Trip Metre A reading is shown. Turn the ignition off.
3. Press and hold the display change button and turn the ignition on (do not start the engine).
4. Continue to press and hold the button until the trip meter displays “”000000″”.”
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

MAINT REQ’D Reset & Service Specifications Toyota Camry 2013

Leave a reply

MAINT REQD light can be reset by doing the following:

1. Press the “”ENGINE START STOP”” switch once (do not start the engine) or turn ignition key to run (one position before starting the engine).
2. Ensure Trip Metre A reading is shown. Turn the ignition off.
3. Press and hold the display change button and turn the ignition on (do not start the engine).
4. Continue to press and hold the button until the trip meter displays “”000000″”.”
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset the oil service light indicator for Volkswagen Tiguan

Leave a reply

How do you reset service light indicator Volkswagen Tiguan year 2010, 2011, 2012, 2013

1. Turn the ignition to run (one position before starting engine).
2. Press and HOLD the trip-odometer button “0.0”.
3. Turn your key to run (one position before starting engine).
4. Release the trip-odometer button.
5. Push and release the Clock Minute Set Button “min”.
or
2. Use the rocker switch on the windshield wiper lever to select “Settings” and confirm with button underneath windshield wiper lever then follow steps 4-5.
or
3. Use the buttons on the right hand side of the multi function steering wheel
4. Select the “Settings” menu followed by the “Service” submenu. Select “Reset” and confirm.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
*vehicles equipped with a navigation system can also access the reset menu from the SETTINGS button.