Tag Archives: ignition

Reset oil service light Subaru Impreza 2014

Leave a reply

How to reset oil service light Subaru Impreza 2014.

Reset service light indicator, engine oil life Subaru Impreza, year 2014 reset instructions:

  1. Turn the ignition to run (one position before starting engine).
  2.  Using the controsl on the left hand side of the steering wheel. Pull the i/Set button towards you to bring up the selection screen.
  3.  Use the Up or Down arrow to highlight the MAINTENANCE menu and pull the i/Set switch towards you.
  4.  Select the maintenance item (i.e. Engine Oil, Oil Filter) and pull the i/SET switch towards you.
  5.  Change the next service date and interval with the Up and Down arrow and confirm by highlighting SET and pull the i/SET switch towards you. The reset is complete when the screen shows Setting Complete.

6. Turn the ignition off and then start the engine to verify the indicator has been reset.
*Reset only available on models with the multi-information display

Reset seat belt reminder light Toyota Land Cruiser 100 series

Leave a reply

How to reset seat belt reminder lightt Toyota Land Cruiser 100 series.

Reset seat belt reminder lightt Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

Driver’s seat belt reminder light and buzzer.

The light and buzzer act as a reminder to buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and the buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light continues flashing and the buzzer sounds 4 to 8 seconds. If the light stay on after you connected the belt you may have a problem with the airbag or with the sensor.

Front passenger’s seat belt reminder light.

The light acts as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. Unless the front passenger fastens the belt, the light continues flashing. If luggage or other load is placed on the front passenger seat, depending on its weight and how it is placed on the seat, built−in sensors in the seat cushion may detect the pressure, causing the reminder light to flash.

To reset the seat belt reminder light Toyota Land Cruiser 100 series you must go to a authorized dealer to reset this warning light for you.

All information are taken from Toyota Land Cruiser 100 series owners manual.

Reset brake system warning light Toyota Land Cruiser 100 series

Leave a reply

How to reset brake system warning light Toyota Land Cruiser 100 series.

Reset brake system warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light comes on in the following cases when the ignition key is in the “ON” position.

When the parking brake is applied.

This light comes on for a few seconds when the ignition key is in the “ON” position even after the parking brake is released.

When the brake fluid level is low.

It is dangerous to continue driving normally when the brake fluid level is low.

When the hydraulic brake booster fails.

If the hydraulic booster causes an problem resulting in poor braking performance, the warning light comes on and buzzer sounds continuously.

Have your vehicle checked at your Toyota dealer in the following cases:

The light does not come on even if the parking brake is applied when the ignition key is in the “ON” position.
The light does not come on even if the ignition key is turned on with the parking brake released.
A warning light turning on briefly during operation does not indicate a problem.

If any of the following conditions occur, immediately stop your vehicle at a safe place and contact your Toyota dealer.

  • The light does not turn off even after the parking brake is released while the engine is running.
  • The warning buzzer comes on together with the warning light.
  • In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.

The brake system warning light remains on together with the “ABS” warning light.

In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

Any of the following conditions may occur, but do not indicate a malfunction:

The light may stay on for about 60 seconds after the ignition key is turned to “ON” position. It is normal if it goes out after a while.

Depressing the brake pedal repeatedly may turn on the warning light and buzzer. It is normal if the light goes out and the buzzer stops sounding after a few seconds.

You may hear a small sound in the engine compartment after the engine is started or the brake pedal is depressed repeatedly. This is a pump pulsating sound of the brake system, and it is not a malfunction.

All information how can you reset brake system warning light is taken from Toyota Land Cruiser 100 series owners manual.

How to check service light Toyota FJ Cruiser

Leave a reply

Checking service reminder indicators on a Toyota FJ Cruiser except the low fuel level warning light.

How to check service light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

Apply the parking brake.

Open one of the side doors, back door or back window. The open door warning light should come on.
Close the door and back window. The open door warning light should go off.
Turn the ignition key to “ON”, but do not start the engine. All the service reminder indicators except the open door warning light should come on.
The following service reminder indicators go off after a few seconds:

  • Engine oil replacement reminder light.
  • ABS warning light.
  • VSC TRAC warning light.
  • AUTO LSD indicator light two−wheel drive models.
  • VSC OFF indicator light four−wheel drive models, and vehicles with rear differential lock.
  • Slip indicator light.
  • The SRS warning light goes off after about 6 seconds. There may be the case that the “ABS” warning light (brake assist system warning light), “VSC TRAC” warning light and “AUTO LSD” (two−wheel drive models), “VSC OFF” (four−wheel drive models, and vehicles with rear differential lock) or slip indicator light stay on for about 60 seconds after the ignition key is turned to the “ON” position. It is normal if they go out after a while.

If any service reminder indicator or warning buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.

All information how to check service light is taken from Toyota FJ Cruiser owners manual.

Reset front passenger’s seat belt reminder light Toyota FJ Cruiser

Leave a reply

How to reset front passenger’s seat belt reminder light Toyota FJ Cruiser.
Reset front passenger’s seat belt reminder light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

The light and buzzer act as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the driver’s seat belt is fastened. If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light may flash and buzzer to sound.

The buzzer can be set not to sound by following the procedure below.

  1. Sit on the front passenger seat.
  2. Turn the ignition key to the “OFF” position with the odometer reading shown. For details see the Odometer and two trip meters om Toyota categories.
  3. Turn the ignition key to the “ON” position.
  4. Within 6 seconds, push the trip meter reset knob and hold it for more than 10 seconds.
  5. Insert the tab of front passenger seat belt into the buckle.
  6. The odometer shows either “b−on” or “b−off”. The reading changes by pushing the trip meter reset knob and the setting of the front passenger seat belt reminder buzzer can be changed. The odometer display returns to normal if the meter reset knob has not been operated for more than 10 seconds or the ignition key is turned to the “OFF” position.

All information how can you reset front passenger’s seat belt reminder light is taken from Toyota FJ Cruiser owners manual.