Tag Archives: warning

Oil reset service light indicator Mercedes Viano 2008

Leave a reply

How do you reset maintenance light, reset service light indicator Mercedes Viano, year 2008, 2009, 2010, 2011, 2012, 2013, 2014. For reset maintenance light and that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Mercedes Viano, oil reset instructions:

  1. Ensure ignition is switched OFF.
  2. Switch ignition ON and briefly press button[A] twice.
  3. Within 10 seconds: Switch ignition OFF.
  4. Press and hold button [A].
  5. Switch ignition ON.
  6. Continue to hold button [A].
  7. The remaining distance will be displayed.
  8. After aproximately 10 seconds a warning sound will be heard and the new remaining distance will appear in the digital display.
  9. Release button [A].

Oil reset service light indicator Mercedes Viano 2008

NOTE: The service interval indicator can be reset to a higher than normal value for use with alternative higher specification engine oils. This can only be carried out using diagnostic equipment.

Oil reset service light indicator Skoda Fabia Mk2

Leave a reply

How to reset service light indicator Skoda Fabia Mk2.

Reset service light indicator Skoda Fabia Mk2. From year: 2007, 2008, 2009, 2010, 2011, 2012, 2013.

oil-reset-service-light-indicator-Skoda-Fabia-Mk2 (1)

 

 

 

 

 

It is only possible to reset the Service Interval Display, if a service message or at least a pre-warning is shown in the instrument cluster display.

We recommend that this reset is completed by a specialist garage.

The specialist garage:

  • resets the memory of the display after the appropriate inspection;
  • adds an entry to the Service Schedule;
  • affix the sticker with the entry of the following service interval to the side of the dash panel on the driver’s side.

You can reset the service interval display by using the reset button 6 from the above picture.

On vehicles which are equipped with the information display, you can reset the service interval display in the menu Settings.

oil-reset-oil-service-light-Skoda-Fabia-Mk2 (1)

First read and observe the introductory information and safety warnings.

You can activate the Main menu by pressing the rocker switch A, formore than 1 second.

Individual menu points can be selected by means of the rocker switch A. When the pushbutton B is briefly pressed, the information you have selected is displayed.

The following information can be selected (depending on the equipment installed on the vehicle):

  • MFD
  • Audio
  • Navigation
  • Phone
  • Vehicle status
  • Settings

The menu points Audio and Navigation are only displayed when the factory-fitted radio or navigation system is switched on.

If warning messages are shown in the information display, these messages can be confirmed with the button B, on the windshield wiper lever in order to call up the main menu.

If the information display is not activated at that moment, the menu always shifts to one of the higher levels after 10 seconds.

Settings Skoda Fabia.

You can change certain settings by means of the information display. The current setting is shown on the information display in the respective menu at the top below the line.

The following information can be selected (depending on the equipment installed on the vehicle):

  • Language
  • MFD Data
  • Time
  • Winter tyres
  • Units
  • Alternative speed displayed
  • Service
  • Factory Setting
  • Back

After selecting the menu point Back you will reach one level higher in the menu.

Language
This is where the language in which the warning and information texts should be displayed can be set.

Displays of the MFA
This is where certain displays of the multi-functional indicator can be switched on or off.

Time
The time, time format (12 or 24 hour indicator) and the changeover between summer/winter time can be set here.

Winter tyres
This where the speed at which a warning signal should sound can be set. This function is, for example, used for winter tyres with which the permissible maximum speed is lower than the maximum speed of the vehicle.

When exceeding the speed, the following is shown on the information display:

Winter tyres: max. speed … km/h

Measures
The units for the temperature, consumption and distance driven can be set here.

Second speed
The display of the second speed in mph or in km/h can be switched on here1).

Service
Here you can have the remaining kilometres and days until the next service interval displayed, and reset the Service Interval Display.

Factory Setting
After selecting the menu Factory setting the factory setting of the information display is restored.

That it is the full procedure how to reset service light indicator Skoda Fabia Mk2. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Skoda cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

Reset tire pressure warning light Toyota Solara 2 generation

Leave a reply

Reset tire pressure warning light Toyota Solara 2 generation. From year: 2004, 2005, 2006, 2007, 2008.

How to reset tire pressure warning light Toyota Solara second generation.

Reset-tire-pressure-warning-light-Toyota-Solara-2-generation

This light warns that the tire pressure of one or more of your tires (including ground spare tire) is low. The light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is functioning properly. If the warning light comes on, stop your vehicle in a safe place as soon as possible and check that the inflation pressure of all tires (including ground spare tire) is as specified on the tire and loading information label.

The light should go off a few minutes after the tire pressure is adjusted.

If the warning light comes on after blinking for 1 minute, the tire pressure warning system may be malfunctioning. Contact your Toyota dealer.

TIRE PRESSURE WARNING RESET SWITCH.

When initializing the system, the present tire inflation pressure is stored as standard. The tire pressure warning system determines decreased air pressure by comparing the present and the standard tire inflation pressures. When you change the set tire inflation pressure, it is necessary to initialize the tire pressure warning system.

  • When changing the tire size.
  • When rotating the tire on vehicles differing with front and rear tire inflation pressure.

To initialize the system, perform the following:

  1. Park the vehicle in a safe place and turn the ignition key to “OFF” position.
  2. Adjust the pressure of all the installed tires to the specified cold tire inflation pressure level.
  3. Turn the ignition key to the “ON” position.
  4. Push and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times.
  5. Leave for a few minutes with the ignition key in “ON” position, and then turn the ignition key to “OFF” position.

If you push the tire pressure reset switch while vehicle is moving, initialization is not performed. If you push the tire pressure reset switch accidentally and initialization is performed, adjust the tire inflation pressure to the specified level and initialize the system again.

If the tire pressure warning light does not blink slowly three times when you push and hold the reset switch, initialization has failed and the tire pressure warning system may not work properly. In this case, initialize the system again. If initialization cannot be performed, have the system checked at your Toyota dealer.

Do not push the reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

That it is the full procedure how to reset tire pressure warning light Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

Reset low windshield washer fluid level warning light Toyota Solara

Leave a reply

Reset low windshield washer fluid level warning light Toyota Solara second generation. From year: 2004, 2005, 2006, 2007, 2008.

How to reset low windshield washer fluid level warning light Toyota Solara 2 generation.

The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity.

Adding washer fluid.

If any washer does not work or the low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. You may use plain water as washer fluid. However, in cold areas where temperatures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

Do not use engine antifreeze or any other substitute because it may damage your vehicle’s paint.

If the low windshield washer fluid level warning light is not gone means that a sensor is broken.

All information how can tou reset low windshield washer fluid level warning light is taken from Toyota Solara ownes manual.

That it is the full procedure how to reset low windshield washer fluid level warning light Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

Reset VSC warning light Toyota Solara second generation

Leave a reply

Reset VSC warning light Toyota Solara second generation. From year: 2004, 2005, 2006, 2007, 2008.

How to reset VSC warning light Toyota Solara 2 generation.

The light warns that there is a problem somewhere in the vehicle stability control system or traction control system. The light will come on when the ignition key is turned to “ON”, and will go off after about a few seconds.

If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.

All information how can you reset VSC warning light is taken from Toyota Solara second generation owners manual.

That it is the full procedure how to reset VSC warning light Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.