Tag Archives: key

Reset front passenger’s seat belt reminder light Toyota FJ Cruiser

Leave a reply

How to reset front passenger’s seat belt reminder light Toyota FJ Cruiser.
Reset front passenger’s seat belt reminder light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

The light and buzzer act as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the driver’s seat belt is fastened. If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light may flash and buzzer to sound.

The buzzer can be set not to sound by following the procedure below.

  1. Sit on the front passenger seat.
  2. Turn the ignition key to the “OFF” position with the odometer reading shown. For details see the Odometer and two trip meters om Toyota categories.
  3. Turn the ignition key to the “ON” position.
  4. Within 6 seconds, push the trip meter reset knob and hold it for more than 10 seconds.
  5. Insert the tab of front passenger seat belt into the buckle.
  6. The odometer shows either “b−on” or “b−off”. The reading changes by pushing the trip meter reset knob and the setting of the front passenger seat belt reminder buzzer can be changed. The odometer display returns to normal if the meter reset knob has not been operated for more than 10 seconds or the ignition key is turned to the “OFF” position.

All information how can you reset front passenger’s seat belt reminder light is taken from Toyota FJ Cruiser owners manual.

Reset charging system warning light Toyota FJ Cruiser

Leave a reply

How to reset charging system warning light Toyota FJ Cruiser.

Reset charging system warning light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

This warning light comes on when the ignition key is turned to the “ON” position, and goes off when the engine is started. When there are problems in the charging system while the engine is running, the warning light comes on.

When the charging system warning light comes on while the engine is running, malfunctions such as the engine drive belt being broken may have occurred. If the warning light comes on, immediately stop the vehicle in a safe place and contact your Toyota dealer.

The charging system warning light can not be reset by using the buttons on the board this light can be reset by the Toyota dealer.

Reset ABS service light Toyota FJ Cruiser

Leave a reply

How to reset ABS service light Toyota FJ Cruiser.

Reset ABS service light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

The light comes on when the ignition key is turned to the “ON” position. If the antilock brake system and the brake assist system work properly, the light turns off after a few seconds. Thereafter, if either of the systems malfunctions, the light comes on again.

When the “ABS” warning light is on (and the brake system warning light is off), the following systems do not operate, but the brake system still operates conventionally.

Anti−lock brake system.
Brake assist system.
Traction control system.
Active traction control system
(four−wheel drive models with rear differential lock)
AUTO LSD system two−wheel drive models.
Vehicle stability control system.
When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate, so that the wheels will lock up during a sudden braking or braking on slippery road surfaces.

If either of the following conditions occurs, this indicates a malfunction somewhere in the components monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle.

The light does not come on when the ignition key is turned to the “ON” position, or remains on.
The light comes on while you are driving.
A warning light turning on briefly during operation does not indicate a problem.

If the “ABS” warning light remains on together with the brake system warning light, immediately stop your vehicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.

Any of the following conditions may occur, but do not indicate a malfunction:

The light may stay on for about 60 seconds after the ignition key is turned to the “ON” position. It is normal if it turns off after a while.
Depressing the brake pedal repeatedly may turn on the light. It is normal if it turns off after a few seconds.
With rear differential lock: The light comes on with rear differential locked. At this time, the anti−lock brake system, the brake assist system, the vehicle stability control system, the traction control system and the active traction control system do not operate.
All information how can you reset ABS service light is taken from Toyota FJ Cruiser owners manual.

Reset VSC trac warning light Toyota FJ Cruiser

Leave a reply

How to reset VSC trac warning light Toyota FJ Cruiser.

Reset VSC trac warning light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

The light warns that there is a problem somewhere in the following.

Vehicle stability control system.
Traction control system.
Active traction control system four−wheel drive models with rear differential lock.
AUTO LSD system two−wheel drive models.
Four-wheel drive models, and vehicles with rear differential lock-the “VSC OFF” indicator light will come on with the “VSC TRAC” warning light if there is a problem somewhere in the vehicle stability control system.

The light will come on when the ignition key turned to “ON”, and will go off after a few seconds.

The slip indicator light will come on with the “VSC TRAC” warning light if there is a problem somewhere in the following.

Traction control system.
Active traction control system four−wheel drive models with rear differential lock.
AUTO LSD system two−wheel drive models.
It is not a malfunction that the warning light may stay on for 60 seconds after the ignition key is turned to the “ON” position. Depressing the brake pedal repeatedly may turn on the lights. It is normal if they go out after a few seconds.

If the light comes on while driving, the above mentioned systems do not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

In the following cases, contact your Toyota dealer:

The warning light does not come on after the ignition key is turned to “ON”.
The warning light remains on after the ignition key is turned to “ON”.
The warning light comes on while driving.
When the brake fluid level is too low, the above mentioned systems will not operate and the warning light comes on.

All information how can you reset VSC trac warning light is taken from Toyota FJ Cruiser owners manual.

Reset ABS warning light Toyota Yaris second generation

Leave a reply

How to reset ABS warning light Toyota Yaris 2 generation.

Reset ABS warning light Toyota Yaris second generation. From year: 2005, 2006, 2007, 2008, 2009, 2010, 2011.

The light comes on when the ignition key is turned to the “ON” position. If the antilock brake system works properly, the light turns off after a few seconds. Thereafter, if the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate, but the brake system still operates conventionally.

When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle.

The light does not come on when the ignition key is turned to the “ON” position or remains on.
The light comes on while you are driving.
A warning light turning on briefly during operation does not indicate a problem.

If the “ABS” warning light remains on together with the brake system warning light, immediately stop your vehicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unstable during braking.